
UNSOLVED
HH
Henry Hahn
1 Rookie
•
7 Posts
0
7504
May 2nd, 2009 18:00
Blue screen messages
First I am a total "idiot" when it comes to these things so please bear with me.
For the last 5 days I have been randomly getting these blue screen messages
***stop: 0x0000007e
*** atapi.sys-adress f736d001 base at f7360000, datestamp 4802539d
***stop: 0x000000f4
a process thread crucial to system operation has unexpectedly exited or benn terminated
I did a system restore back to a point from last week prior to the problem starting but it again gave me a blue screen message just minutes after restarting the laptop.
Any ideas?
The system is a Inspiron 6000, operating system is XP Media Center Edition. No new software or hardware. It has the AVG free virus program installed.
Thanks
Hank
Responses (10)
Solutions (0)
Henry Hahn
1 Rookie
•
7 Posts
562
0
Posted May 3rd, 2009 09:00
Ok, here ignorance will shine through.
When I press F12 during the powerup here are my choices
Internal HDD (when I click on this and hit enter the laptop starts up windows immediately)
CD'DVD/CD-RW Drive
Cardbus NIC
Onboard NIC
BIOS setup
Diagnostics
When I arrow down to diagnostics and hit enter it goes into
"Pre Boot Sysmtem Assessment Build 3018"
it stops/ends at the line (all the tests come up "pass")
DST Short Status Test - pass
And I get a message box
"No diagnostic Utility Partition found. To run diagnostics insert your Dell "Drivers and Utilities" CD. Then select Ok to restart the system and boot off the CD"
I am sure the only Dell CDs I have are the ones that came with my desktop unit which is much older. Last year, 14 months ago, I had to replace the Hard Drive on the laptop while still under warranty and Dell sent me a OS CD to install on the new hard drive. For the drivers they gave me a bunch on tinyurls to download them from. Is there somewhere I can down load the diagnostics from?
Thanks again for any help you can provide
You need to download the ISO file and use your CD writer package to make a bootable CD from it (you CANNOT simply write the ISO file to CD - you MUST use a CD writer package - Roxio, Nero, etc.) to make a bootable CD from that image.
Henry Hahn
1 Rookie
•
7 Posts
562
0
Posted May 3rd, 2009 11:00
Downloaded it. unzipped it. But when I run diagnostics (F12 at startup) it does not give the option or run it.
What do I need to do next!
Sorry
Henry Hahn
1 Rookie
•
7 Posts
562
0
Posted May 3rd, 2009 14:00
Ok, I did this using Roxio Creator LE. Now how do I boot from this CD?
Henry Hahn
1 Rookie
•
7 Posts
562
0
Posted May 3rd, 2009 15:00
I knew that sounded too easy. I am as I said a complete dope.
When I do this, windows boots up.
My son stopped by and did have me do a hard drive test at pcpitstop.com and no problems were found.
Henry Hahn
1 Rookie
•
7 Posts
562
0
Posted May 5th, 2009 09:00
Still trying to figure out what is going on her.
As of this morning my desktop background is gone. And I got a "corrupt file" message. Ran Check disc and it did not report any errors from what I can tell (After it finiishes running it flashes momentarily information on the disc and then boots up Windows.)
I still can not get the Dell hard drive diagnostics to run. I think the original disc I made whith the ISO file was not correct as I believe my Roxio program is not "complete" and thus was not making the "bootable" image. I went to magiciso.com and used their freware and I think I did it right, but still I can not get the utility diagnostics to run.
Any ideas anyone?
I guess the good news is that after all this started I finally purchased an external HD and have backed up everything to it via "snapshot", just in case.
David_Heath
7 Posts
149
0
Posted July 5th, 2009 01:00
If you are using Roxio, you need to open their "Disk Copy" and when it asks copy from what, tell it ISO and show it which one. Will the result boot at all?
Sounds like you found it since you have not come back, but be aware that on my laptop, trouble with a modular drive may give you a 0X000000F4 0X00000003... message also. So your DVD drives, etc might be the problem. If you have one, try removing the modular drive while shut down. Then boot and if you can, go to Start/Control Panel/Administrative tools/Event Viewer/System. Look for a recent red circle with an X. Right click on it and choose Properties. With luck there will be a note there of what happened.
You can also look in start/help for info on Using Dr. Watson. Dr. Watson did not show anything on my 0X000000F4 0X00000003, but don't throw away any opportunities.
If it is a bad connection, like the connector on the drive, I have found that STABILANT 22A makes them MUCH more reliable. It is expensive, but I have been using a 15mL bottle for 6 or 8 years and it is still 1/3 full. Get a small water color brush or some kinds of women's make-up brushes. Cut the handle to about 3" long and attach it with a rubber band around the bottle. Then, when you want to use it, first make sure there is no dust or corruption anywhere like on the male or female pins of the connector. Then remove the brush from the bottle, moisten the bristles with a drop of 22A and paint the contacts. Don't be sloppy. Don't damage anything, like the gold contacts with the hard parts of the brush, like the ferrule. A large connector might want 2 or 3 drops, but it does not take much. Just lightly moisten it. With all power off plug it in and remove it several times to wipe the mating parts. Then store the brush with the bottle using the rubber band in a CLEAN place. Perhaps a Zip-Lok bag.

ejn63
11 Legend
•
87469 Posts
•
321256 Points
562
0
Posted May 2nd, 2009 19:00
Press F12 at powerup, boot to the Dell diagnostics, and run the extended (NOT just the quick) test on the hard drive, which I suspect you'll find has developed bad sectors and is therefore in need of replacement.