
UNSOLVED
Closed
F
fenderguitarguy
328 Posts
0
9258
March 4th, 2005 14:00
Arctic Silver
I want some of the regulars to answer this question.
What do you think about Arctic Silver? Is it worth getting?
Responses (10)
Solutions (0)
insp1150_14CK56
363 Posts
445
0
Posted March 4th, 2005 23:00
Artic silver is an excellent compound. I use it as soon as I get a system, out goes the old stuff.... :)It will cool your Notebook from 4-20 Celcius lower than normal cheap Thermal paste and a Desktop up to double that...
I just had Dell out to look at my 5160, which wasn't booting...After 3 services calls, due to the Indian Desk, shipping the wrong parts(Although they all were put in anyway... ;)
I ended up with a new MOBO, P4 mobile 3.2Ghz 533fsb CPU, 5200FXgo Video card, 2x 512 DDR 333Mhz(512MB was an upgrade, for my hassle), New Palmrest, power-switch(which was all that was originally wrong, when I tested it, with my volt-meter), Plus a new blue back of LCD screen W/Dell logo...and new XPproSP1 sticker, as mine was almost melted off...I'm now waiting for a new 60GB 7200 HDD, as the kid dropped my notebook onto the floor(If anything else goes wrong, they will be replacing the LCD display as well, due to that drop occuring)...only thing then would be the case bottom, which I've already made a mold of, & am in the process of Modding now !!!
I insist, on using the Artic Silver 5 as it has 5 particles(as to three particles on the older vers.) & more silver 99%, as opposed to AS 3 or the older stufff, not they won't keep your CPU cooler, just that AS 5 has kept all my Intel & AMD cpu's the coolest
However on AMD 64, use the AS ceramique, AS - AS 5, is known to remove the exteririor portion of the HS die, over a short period of time, leaving the CPU open to failure, within 3-6 months.
Not that Dell sells any Boxes with the 64Bit AMD's in them, but for you home-builders, this will save you from voiding the warranty as AMD knows when AS non ceramique has been used, even if you clean it off a dead CPU !!!
Regards in a cooler CPU,
Mer
MightyMack
95 Posts
445
0
Posted March 5th, 2005 16:00
Iopened the video card heat sink on my I8600 and noticed that there was a thermal pad (rubber like material) . Should I go ahead and apply arctic silver on the Video chip anyway? WIll this interfere with the thermal pad ?
Also will applying AS void the warranty?
insp1150_14CK56
363 Posts
445
0
Posted March 5th, 2005 16:00
No, I would remove the pad and install the AS.MightyMack
95 Posts
445
0
Posted March 5th, 2005 17:00
But there will be a space between the chip and heatsink if I remove the pad. what do I put there. AS will not fill it.insp1150_14CK56
363 Posts
445
0
Posted March 5th, 2005 17:00
Apply some AS to the pad, do not remove it.DO NOT remove the pad and read this to apply.
http://www.arcticsilver.com/arctic_silver_instructions_big2.htm
- I think you should remove the pad, & clean all surfaces... figure out, how thick you pad was, & get a piece of copper(from a small sheet of copper) slightly thinner than your pad...Add AS 5 to both sides of the copper square, you cut to equal the pad size, & that will give you a perfect fit, plus supeior cooling for your Vid card

boppo
2 Intern
•
4376 Posts
445
0
Posted March 4th, 2005 15:00