UNSOLVED

Dan_Honemann

updated

21 years ago

0

21339

December 28th, 2005 09:00

What are the system board configuration jumper settings for the 8250?

My Dimension 8250 system board has a configuration jumper on it which is shown in the diagram in the user guide here:

http://support.dell.com/support/edocs/systems/dim8250/techov.htm#1084976

Unfortunately, the illustration shows the configuration jumper (CLR CM) but gives absolutely no further information on it--such as what pins the jumper should be straddling.

Meanwhile, the document on how to clear the NVRAM on a Dell Dimension PC here:

<ADMIN NOTE: Broken link has been removed from this post by Dell>



... seems to incorrectly state procedures for the 8250 (or else the mobo I got for my 8250 is actually an 8200 or 8300), as it states "You need to jumper the system board to Maintenance Mode and then reset configuration data" but offers no further information on how to do that (nor does the 8250 user guide). Furthermore, the BIOS setup instructions that follow do not seem to fit my 8250 A04 BIOS, while the instructions in the section above (presumably for the 8200 and 8300, etc.) *do*--i.e., press F2 to enter system setup, Esc to exit and save (rather than F10), and so on.

And yet... my 8250 system board does indeed have this "maintenance jumper" or "configuration jumper"--I just have no documentation on how to use it. Since this is a replacement motherboard that Dell has shipped me, I am concerned that the jumper may be set incorrectly as I have been experiencing problems trying to use my PCI cards (the same cards that worked fine with my original 8250 motherboard). So I am looking for clarification on how this configuration jumper should be jumpered; it is currently jumpered across the two right-most pins (looking from the back of the PC; there are three pins altogether).

Can any Dell Technical Support person (or anyone who knows) please inform as to exactly what this configuration jumper is for and what the options are for setting it?

Thanks,
Dan

Message Edited by Dan_Honemann on 12-28-2005 06:31 AM

Message Edited by Dan_Honemann on 12-28-2005 06:32 AM

  • 1138

    0

    Posted December 28th, 2005 09:00


    @ejn63 wrote:
    1-2 is normal, 2-3 is clear password/XCMOS, no jumper is BIOS recovery mode.


    Are you sure about that? I only ask because there is a separate "password jumper (PSWD)" on the 8250 mobo (see the user guide reference I linked above). You may be referring to the jumper settings for an XPS system.

    Would 1-2-3 be the order of the pins from left to right when viewing the jumper from the rear of the mobo (from behind the PCI slots)?

    Thanks,
    Dan
  • ejn63

    11 Legend

    •

    87469 Posts

    •

    321256 Points

    1138

    0

    Posted December 28th, 2005 09:00

    1-2 is normal, 2-3 is clear password/XCMOS, no jumper is BIOS recovery mode.
  • ejn63

    11 Legend

    •

    87469 Posts

    •

    321256 Points

    1138

    0

    Posted December 28th, 2005 10:00

    Oops - on the ones with the separate password jumper, the other jumper is just a CMOS-clear (as above - 1-2 normal, 2-3 clear, no jumper, recovery). Pin 1 should be marked on the board itself.
  • 1138

    0

    Posted December 28th, 2005 12:00

    Thanks very much for that! I will check the board next time I have the case open and see if I can spot the "1." It may be useful to clear the NVRAM this way.

    Cheers,
    Dan