UNSOLVED

mmainprize

updated

23 years ago

M

mmainprize

260 Posts

0

28677

April 16th, 2004 01:00

Dimension 4550/8250/8300/XPS Front Headphone Jack Noise/Hiss

Poll question, is anyone with a new Dimension PC (less the one month old) Still having this problem?

Dimension 4550/8250/8300/XPS Front Headphone Jack Noise/Hiss has been an ongoing problem for many of us for months now and Dell has stopped reporting what will be done about this. I have not seen any new messages about this problem. So i am wondering if they have fixed it in the new PC's and just don't want to fix it in all the PC that have been sold for the last nine months.

The problem is the front jacks for the headphones and the MIC. Both have noise and it is so bad that the mic will be very noisey, and the buzz in the headphones when you move the mouse or scroll the screen with text on it. There is a sticky post in this forum about this problem it has been locked.

Please reply if you have a new PC and it still has this noise problem. Thank You.

Message Edited by mmainprize on 04-15-2004 10:02 PM

  • wavlet

    31 Posts

    584

    0

    Posted April 23rd, 2004 19:00

    Have this problem too.  Using the microphone connector from the rear of the PC solved this problem.  I had the front panel board replace as well as the cables.  When the technician did the replacement, I examined the cables.  There was no shielding!  This is poor engineering design practice and is the reason for the noise on the microphone & headphones. 
  • ascher

    5 Posts

    584

    0

    Posted April 30th, 2004 19:00

    Did the repair fix the buzz problem? Your message doesn't say.
  • TomXPS

    1310 Posts

    584

    0

    Posted May 2nd, 2004 22:00

    I have a XPS purchased in Dec, with the same problem tried the front jacks and finally moved to the back to get acceptable sound.   Curious if I have Dell come out and fix it, will it be better. 

    Would really like to have the front ones work, seem like they could do a better job.

     

     

  • wavlet

    31 Posts

    584

    0

    Posted May 2nd, 2004 23:00

    Dell came out and replaced my front-panel.  I had an opportunity to examine the board and interconnect cables.  The cables did not have any shielding. This was either an engineering oversight (poor attention to detail) or a cost-reduction measure.  Unfortunately, unless they change their design, a fron-panel board and cable swap will not do anything.  I still have the noise problems in my front panel so I use the direct connections from the rear. 

    Dell needs to either fix this problem or stop claiming they a front panel audio interconnect solution, which they clearly do not.  The audio board , which Dell does not manufacture, may need some additional modifications to have a robust interconnect. This may be part  of the problem, as this might be too expensive a retrofit for them.  However, for those of us who were enticed with the front-panel audio interconnects, I think Dell should do the honorable thing and fix the problem.   At the very least, they should stop advertising the front panel audio interconnects for the PCs they currently sell.   

     

  • ROWALA

    3 Posts

    584

    0

    Posted May 15th, 2004 21:00

    I bought a Dimension XPS in late January.  The front panel microphone jack was unusable.  On four different occasions, technicians successively replaced all of the cables, the front panel assembly and circuit board, the sound card and ultimately, the motherboard.  Finally, Dell shipped me a brand new unit in April.  Unfortunately, if anything, the new one is worse.  The microphone jack is still unusable.  It appears to be a function of poor engineering (surprising in such a high end system).  I intend to raise the issue once again with our account manager and regional account representative.
  • wavlet

    31 Posts

    584

    0

    Posted May 16th, 2004 02:00

    I think Dell has elected to ignore this problem.  They will continue to send out technicians to fix this problem with component replacements, but this won't work because the problem is an engineering design flaw of the audio subsystem.   I think Dell believes it is cheaper for them to do these replacements until the consumer gives up than to re-engineeer the audio subsystem and do field retrofits.   I suspect the front panel issue, while a dissappointment to many users, is not critical enough with the rear-panel workaround for a sufficient number of people to take more drastic action like a product return or class action suit. 

    Save yourself some aggravation.  Decide if you want to keep or return your computer.   If you want to keep the computer give up on Dell fixing this issue and  go to Radio Shack and buy a couple of audio extension cables to bring the rear microphone/headphone panel jacks to the front/top of the computer for $15-20.  (Hey, Dell - this might be a cheap work-around for you and smart from a business perspective.  This certainly is cheaper than sending techs out and air-shipping defective components.)  If you are connecting the audio to/from a receiver, you may want to buy a ground-loop isolator (also from Radio Shack) to remove 60 Hz power-line hum.

    Other than the front-panel issues, I do like my Dell.  They've been very reliable computers for me, allthough a bit pricey.  I do think Dell is being a bit penny-wise pound-foolish with this issue.  Their lack of response will certainly be a consideration in my next computer purchase.

    Good luck!

       

     

     

     

  • ROWALA

    3 Posts

    584

    0

    Posted May 16th, 2004 15:00

    The other option might be for Dell to replace the OEM version of the Audigy2 soundcard with the retail version of the Audigy2 Platinum which includes a front panel "I/O Platinum Drive" that would occupy an unused 5-1/4" bay and provide the following inputs and outputs:


    Audigy 2 ZS Internal I/O Drive Front Panel Connectors:

    Headphone Out (1/4” Stereo Jack)
    Line In 1 (1/4” Stereo Jack , shared with Microphone In with Gain Control)
    Two RCA jacks for Auxiliary input
    Optical SPDIF In/Out
    SPDIF In/Out
    Digital Out for 5.1 support (6-channel SPDIF Output to Creative digital speakers)
    FireWire® (IEEE® 1394) port
    MIDI In/Out
    Infra-red Receiver




    I would think that even that would be much more cost efficient than all of the ineffective "solutions" that were attempted with my unit.

  • 584

    0

    Posted October 16th, 2010 19:00

    Well i do think this way too, they ignored this, its 2010 now and I have the same issue.

  • rdunnill

    8 Professor

    •

    8811 Posts

    •

    35254 Points

    584

    0

    Posted November 2nd, 2010 00:00

    I installed a Soundblaster card in my 4550, which I pieced back together after I found it on the company scrap heap. I used the front audio jack extensively and don't remember any problems.