UNSOLVED

mnscaper

updated

20 years ago

M

mnscaper

3 Posts

0

12699

August 10th, 2006 19:00

How do I tell if I have IDE or SATA

I have been having problems booting my Dimension 4300. Started out with a operating sytem error while trying to power up. Now I just get a black screen with a blinking cursor unless I enter either start up menu or boot menu. Boot menu only gives me the following options:
1. normal
2. diskette
3. Hard drive
4. cd rom
no choice of safe mode or dell diagnostics.
 
When I try to boot from the XP disk included with my computer it wants to reformat and start over. Repair console wants to rewrite my MBR.
I am at the point where I am ready to junk this computer but desprately want to recover some files off of it before doing so (photos of the kids that kind of thing). I have been told the best way to do that would be by piggybacking another drive but that first I need to know if this drive is IDE or SATA. How do I figure that out? Or any suggestions what else to try?
 
Thanks!
  • shesagordie

    12 Elder

    •

    46017 Posts

    319

    0

    Posted August 10th, 2006 20:00

    mnscaper
     
    The D-4300 does not support SATA, this system only supports IDE/EIDE/ATA hard drives.
     
    Have you tried running diagnostics from the Dell Drivers & Utilities CD?
     
    Bev.
  • mnscaper

    3 Posts

    319

    0

    Posted August 10th, 2006 23:00

    Hi Bev,

    Thanks for responding. I had not tried that before so I just did. It ran just fine without any errors until it got to something called confidence test. It came up with this message:

    An additional sense information

    IDE Disk 0 - Confidence test :Fail

    Status: Fail  Status Code: DOS DDG-D Disk 192 040

    Device IDE_Disk_0 Test: Confidence_Test-Read_Test
    Release: 1073 Module(s) Disk

    Msg: Block 18053: Timeout waiting for drive not busy.

    It has repeated this for an error count of 52 and is still running. Not sure what to do from here.

    Thanks! 

  • shesagordie

    12 Elder

    •

    46017 Posts

    319

    0

    Posted August 10th, 2006 23:00

    mnscaper
     
    The hard drive [IDE Disk 0] is failing and should be replaced. If the system is under warranty, contact Dell for a replacement.
     
    Bev.
  • mnscaper

    3 Posts

    319

    0

    Posted August 11th, 2006 14:00

    Hi Bev,

    I had pretty much figured that out. The computer is 5 or 6 years old by now so I am sure there is no chance it is still under warranty. That is why I am trying to figure out a way to salvage some of the files on the disk beore trashing it. However running the utility seems to have tipped the balance - the setup utility no longer recognizes my hard disk or my cd rom drive. So I guess I am back to trying to piggyback the drive and running a salvage or data recovery program on it. Thanks for trying to help and answering the original question!

  • shesagordie

    12 Elder

    •

    46017 Posts

    319

    0

    Posted August 11th, 2006 18:00

    mnscaper
     
    Thanks for the heads up.
     
    Bev.
  • sherville7

    49 Posts

    319

    0

    Posted August 15th, 2006 21:00

    "How do I tell if I have IDE or SATA"

    IDE drive has a thick, gray cable, it usually looks like a seatbelt.

    SATA drive has a thinner cable. If I remember correctly, it's color blue and much thinner than the IDE

  • Cybervee

    166 Posts

    319

    0

    Posted August 18th, 2006 11:00

    This is an SATA cable -

    http://www.alleycatcables.com/category.aspx?categoryID=48

    This is an IDE cable -

    http://www.ateck.com/viewItem.asp?idProduct=453054800