BIOS Version: A29, A29 (latest as of 18. July 2018)
I have read about NVMe M.2 SSDs and that you either install them on a NVMe M.2 socket on the motherboard or by using the PCIe lane. Now above motherboard has no NVMe M.2 socket (it's too old), but instead it's possible to use an adapter on the PCIe lane.
In the image I attached you can see that there are 2 PCIe lanes. A blue PCIe x16 Connector (6) wired as x16 (Rev 3.0) and a black PCIe x16 connector (5) wired as x4 (Rev 2.0). I have my graphics card listed above on my blue PCIe x16 lane, it's dual width hence it covers the black PCIe x16 (wired x4) socket. Now there is still a little room left between the GPU and the black PCIe lane. I would like to put a PCIe riser in that black PCIe lane and then put an adapter on there to connect a NVMe M.2 SSD.
My questions:
1. I need a flexible riser that can be curved around the GPU, maybe with a flat ribbon cable. Would I go for a x16 to x4 riser? Or x4 to x4 riser? Or x4 to x16 riser? Want kind of riser do I need? 2. Are there risers which go directly from x4 or x16 to an NVMe M.2 adapter on the other end? Basically a riser and adapter in one. 3. Is it important to take a full length x16 riser as base eventhough it's only wired as x4? Or do you just directly pick a riser with x4 as base. If so, on which side of the PCIe lane are the wires connected? Towards the plastic switch/clip or towards the other side? 4. Will the equipment on the black PCIe lane slow down the GPU on the blue PCIe lane due to some shortage? 5. As can be seen in the image I attached, the maximum wattage on the black PCIe lane is 25W. Will one NVMe M.2 SSD need the whole 25W or can for example another NVMe M.2 SSD (or multiple) or a WiFi PCIe Adapter be connected to it also? Would you then take a riser/adapter that goes from x4/x16 to x16 so every SSD/WiFI adapter can fit on one "risen lane", as you could potentially fit 4 times x4 adapters on one x16 "risen line". Correct? 6. Side questions: Would you pick a WiFi PCIe Adapter over a WiFi USB Adapter which you just plug into an USB 3.0 port in the front/back panel of the PC? If so, why?
Sorry for the long text, I think it was needed to cover everything I need to know. If you can help me out I would really appreciate it. If you can suggest some good products, please post the links in your comment!
Just once more for clarification, I want to go FROM the PCIe lane (with a 4x or 16x male?) TO a M.2 NVMe connector (female?) with a (flat ribbon) cable inbetween to then put a M.2 NVMe SSD IN that M.2 NVMe connector.
Either by putting a riser in the PCIe lane and on top of that an adapter or a kind of "extended" (by cable) adapter or a riser with an adapter on one end.
I can only answer part of your question. You can use a PCIx4 card in a x16 slot. That goes with a extension ribbon for a raiser card too. However, it's going to be a tight fit. It is simpler just to buy a bigger SSD and replace one of the existing hard drives.
Thanks for your reply! Yes it's going to be a tight fit, but I would like to give it a try nevertheless. Can you recommend any good riser with flat ribbon cable?
KovenYT
15 Posts
2068
0
Posted December 13th, 2019 17:00
Thank you for approving my thread.
Just once more for clarification, I want to go FROM the PCIe lane (with a 4x or 16x male?) TO a M.2 NVMe connector (female?) with a (flat ribbon) cable inbetween to then put a M.2 NVMe SSD IN that M.2 NVMe connector.
Either by putting a riser in the PCIe lane and on top of that an adapter or a kind of "extended" (by cable) adapter or a riser with an adapter on one end.