MXL: MAC learning not working with lacp ungroup feature configured
Hello Community Engineers,
I need your assistance to clarify how the "lacp ungroup" feature works on MXL Force10 switches configured in a stack.
We have encountered very specific behavior when this feature is enabled and the server wasn't configured with LACP enabled.
Obviously, the switch didn't bring the port-channel up and continued working in independent mode, however, we don't see any mac-address behind physical ports (acting as independent members of ungrouped lacp). See the outputs below:
Port-channel exists and in down state
#sh int port-channel brief | grep down L 1 L2 down 00:00:00 L 23 L2 down 00:00:00
Port-channel 23 is configured with lacp ungroup feature
Codes: *N - VLT Peer Synced MAC *I - Internal MAC Address used for Inter Process Communication VlanId Mac Address Type Interface State rsnr-ch01-switch#sh mac-address-table interface tengigabitethernet 1/26
Codes: *N - VLT Peer Synced MAC *I - Internal MAC Address used for Inter Process Communication VlanId Mac Address Type Interface State
Yes, in a normal situation, the server boots up over iscsi boot or pxe, and mac addresses are available through the port-channel interfaces.
At some moment, we've got into the situation where we had to keep a similar server without LACP for some temporary project and switch configuration stayed unchanged with "lacp ungroup"
#sh ver Dell Real Time Operating System Software Dell Operating System Version: 2.0 Dell Application Software Version: 9.14(1.8) Copyright (c) 1999-2018 by Dell Inc. All Rights Reserved. Build Time: Mon Sep 30 04:17:39 2019 Build Path: /build/build01/SW/SRC Dell Networking OS uptime is 5 week(s), 1 day(s), 22 hour(s), 54 minute(s)
System image file is "system://A"
System Type: MXL-10/40GbE Control Processor: MIPS RMI XLP with 2 Gbytes (2147483648 bytes) of memory, core(s) 1.
I'm not that good with networking, but I had a word with my co-worker about the issue that you had. He was mentioning, since the server is not setup with LACP, you probably might need to configure the switch port as access port only.
DELL-Joey C
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did.
It is a definitely valid answer. In the ideal case yes, we have LACP configured on both sides, however, as I said in certain scenarios we're facing the case where servers still don't have LACP configured and that's why switches are configured with "lacp ungroup" feature
The provided output from interfaces which doesn't have mac-addresses behind them still forwarding traffic, but it looks like the mac-learning feature went offline.
This is 100% reproducible, I want to clarify if this is expected behavior or not. Should we see mac-addresses behind interfaces configured as a port-channel with lacp ungroup feature enabled?
The reason why I'm asking this, because "lacp ungroup" feature and its behavior is barely documented on the website
The only documentation I can find, it's not from the support site, but an external site: https://dell.to/3ABeMD2
I don't have the environment to test the output of the configuration that you're on, I'm unable to verify that LACP ungroup feature should list the mac-addresses, probably you can try to check by running the command:
#show mac-address-table interface port-channel 23
DELL-Joey C
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did.
DELL-Josh Cr
Community Manager
•
9801 Posts
•
45350 Points
1248
0
Posted August 11th, 2021 16:00
Hi,
What version of the OS is on the switch? Does this only happen when the server isn’t configured for LACP?