
UNSOLVED
XPS B933 - (1)r suffix, (2)noisy fan, (3)CD-RW not working
I purchased a (refurbed) XPS B933 in November 2000, with Win98SE preloaded (tag JY12101).
(1) What is the relevance of the 'r' suffix for this model? My original invoice refers to B933, but the Dell support site refers to XPS B___r, based on the service tag. Some drivers and updates refer to the model number with the suffix, others without.
(2) The machine seems noisy compared to other Dell machines I have owned or used. This is due to the fan cooling the CPU (NMB Model 3610KL-04W-B67). Is this normal, should I buy a straight replacement fan, or is there a better (quieter) compatible unit available?
I recently reformatted and repartitioned the hard disk, to install Win2K (my preferred O/S, matching my other home and work machines), but the install always 'hung' after copying the files. Since I could not figure what was stopping this 'clean install', I decided to re-install Win98SE, then upgrade. After some frustrations, I discovered it was necessary to install the Intel Chip Set Update Utility driver (!) and all appears to work, except the CD-RW . . .
The IDE configuration is:
Primary master: IBM-DTLA-307045
Primary slave: Iomega ZIP 100
Secondary master: Samsung DVD-ROM SD-6
Secondary slave: LG CD-RW CED-8080B
(I would also appreciate feedback on whether this is the 'best' configuration, since I have seen conflicting advice about putting the two optical drives on the same channel, and if the CD-RW should be set as a master).
I have tried changing various things in the BIOS set-up - if the CD-RW is recognized by Windows, the system freezes (and needs to be rebooted) doing anything that tries to access the drive (even opening My Computer). However, Device Manager indicates that everything is in place and working normally, including the LG drive. I have also been able to boot without Windows recognizing the CD-RW drive (not sure what's different!) and then everything works fine, except the drive does not exist in Windows (it appears recognized by the system, and can be 'ejected'). I also applied the latest Firmware update available for the CD-RW, but this made no difference.
I would like to get this configuration working properly, so I can move on with the upgrade to Win2K . . . !
Responses (9)
Solutions (0)
- Which BIOS version do you have? If you don't have the latest you may want to think about installing the latest revision.
This the exact model of my main system by the way,.. and I can report 3 years of faithful service and still running strong.
I'm now running XP Pro on it, and I've added a couple of new things (extra hard drive, new high-end vid card, maxxed out the RAM) but it's currently as good, if not better as the day I got it.
I hope you have as much luck with yours as I did with mine.
Ed Thanks for your feedback. The fan has not got worse, but always seemed relatively noisy. Am thinking of having this system on most of the time, as an internet gateway for our home network, so wanted it quieter, if possible. Given your comment about RAMBUS memory running hot, should I reconsider leaving the machine on for extended periods, or will the extra fan/shroud do its job effectively?
I will try reinstalling the drivers, since I did not use the Intel IDE controller driver.
BigBrother
2 Intern
•
4801 Posts
719
0
Posted May 19th, 2003 01:00
Mike9047,
As long as the system has adequate ventilation around it, leaving it on should not present any problems. I would, however, open the case and blow out all of the dust that has accumulated inside. Do NOT vacuum it out. Purchase some canned air and use that to blow the dust out.
Steve
A few of these problems (not the fan) may just go away with a full, clean install of an updated OS. I have been running XP since Jan. without a single crash or hardware weirdness. Most of the proper drivers installed when I installed the OS.
FYI: My fan gets noisy when the room temp gets pretty high, say high 80's, 90's, or above. Right now it's a steady, but tolerable whirr. Fans are a cheap, easy replacement though, and if you spend a little more you can get even quieter ones. The fan on my old (stock) vid card was pretty loud, however. Since I upgraded to the Leadtek the whole system has been a little quiter.
Good luck,
Ed
I'm pretty sure they're fairly standardized. You may have to do a little work to get at the fan(s) itself, since it's behind the shroud/ scoop,.. but I think you'll find as long as the replacement is the same size and has a similar power requirement it should work the same. http://docs.us.dell.com/docs/systems/dmag/rr.htm#chassis_cooling_fan_assembly

BigBrother
2 Intern
•
4801 Posts
719
0
Posted May 18th, 2003 18:00
Mike9047,
(1) The "r" indicates that yours is an Intel Pentium 3 "coppermine" processor. Drivers for either (with or without the "r") should be the same.
(2) You can, of course, purchase a new fan if you want. If the fan sounds the same as when you got the system, I would not worry about it. It has to keep the processor cool along with RAMBUS memory which runs very hot.
(3). After an OS reinstall of Win 98 or Win 2K, the Intel 820 chipset driver should be the next driver installed. You should then install the Intel ATA-66 IDE controller driver (not the Promise ATA-66 driver). Your system has an on-board Intel ATA-66 IDE controller.
(4) In Dell Computers, the easiest way to configure your IDE drives is to set them to Cable Select. In this way, the drive on the end of the cable becomes "master" and the drive in the middle of the cable becomes "slave". It makes configurations much easier. Do not mix "cable select" and "master/slave" jumpering on the same cable. This can cause your system to not boot or even to not post.
(5) Having both optical drives on the same IDE channel should cause no real problems. If you burn directly from a CD-ROM drive to the CD-RW drive, you may experience buffer underruns, but you can work around this problem by either reducing the burn speed or by copying to the hdd first before burning to a CD.
(6) If you want to put Win 2K on your computer and you want to use Easy CD Creator software, you must use version 4.x or newer.
Steve