UNSOLVED

phrogman35

updated

19 years ago

0

14917

November 20th, 2006 11:00

XPS 410 Bios

Received a xps 410 system with XP Media center installed.

Wanted to install my copy of XP Pro and partition the disk into 2 partitions.

I formated the disk and was unable to install Pro due to RAID config or SATA drivers.(I don't have a floppy and didnt feel like slipstreaming them in)Got this....

A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

Check to be sure you have adequate disk space. If a driver is identified in the Stop message , disable the driver or check with the manufacturer for driver updates. Try changing video adaptors.

Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable componenets, restart your computer, press F8 to select Advance Startup Options, and then Safe Mode.

Technical information:

***STOP: 0x0000007E

Dell support had me shut off RAID configuration in BIOS and was able to install my pro copy.

Due to another issue I decided to format again and reinstall XP Media Center.

However,I never changed my BIOS settings back to factory config with RAID enabled.

My question is this, would I now be able to go into my bios and enable RAID with my current install of XP Media center without screwing up anything. I am asking cause I am considering buying another hard disk in the future and set up the system for RAID 1.

TIA

Message Edited by phrogman35 on 11-20-200608:00 AM

  • 330

    0

    Posted November 20th, 2006 15:00

    Ill give it a try, I assume I can download the Matrix manager software from Dell's download drivers and software for my model machine...

    Thanks
  • keithg2

    2 Intern

    •

    935 Posts

    330

    0

    Posted November 20th, 2006 15:00

    Yes, you can enable RAID in the system BIOS and setup your RAID 1 array volume. I can't remember if you can rebuild your RAID 1 mirror by setting "Create raid array using existing hard drive" in the system BIOS.
     
    If you can't, then when windows starts up, go into the Intel Matrix Storage Manager console and create your RAID 1 array by using "Create raid array using existing hard drive". This will mirror the new install to your 2nd hard drive and you're good to go.
     
    Good Luck!
  • 330

    0

    Posted November 20th, 2006 23:00

    The software should be on the disk that came with your 410.  I added another HD and the matrix software took care of everything.  I didn't have to formatt the drive.  Just installed hd, went into matrix, selected raid 1 and done.
  • gdwrnch3

    2 Intern

    •

    3278 Posts

    330

    0

    Posted July 15th, 2007 15:00

        If you are going to format a raid and do a re-install. Disconnect all your drives and readers except for your array, and your DVD, this will insure that the raid array is assigned drive letter C:


    Message Edited by gdwrnch3 on 07-15-2007 12:47 PM
  • gdwrnch3

    2 Intern

    •

    3278 Posts

    330

    0

    Posted July 15th, 2007 15:00

         Personally, I would create the array using the raid bios, and then install your OS.
     
            That is the way I do it, I'm sure you will get tons of other opinions.  I have never migrated to an array, so I can't say how good it works or not.
           I like to start fresh.
    Good luck with what ever you choose to try,
    jd
  • oatmealJS

    1 Rookie

    •

    12 Posts

    330

    0

    Posted July 15th, 2007 15:00

    So it's not better to just do a normal install to a single disk, and then add the RAID after it's all done?
  • oatmealJS

    1 Rookie

    •

    12 Posts

    330

    0

    Posted July 15th, 2007 15:00

    When I got my new XPS-410 last year, I formatted and re-loaded windows first. For some reason, the install named my system drive 'H' instead of 'C'. I think it had something to do with MSM or the BIOS not seeing the RAID array as a primary drive and it found all the other drives first.
    It hasn't been a real problem, just an annoyance at times. There was another solution regarding initial setup, but this idea sounds much easier.
    Next time I'll just disconnect one of the drives, load the OS on the remaining drive as a single disc, and then use MSM to create a RAID array AFTER the install. Should work a lot easier...
    Anyhow, just a musing on an old thread.