UNSOLVED

tim5ny

updated

20 years ago

T

tim5ny

42 Posts

0

3160

May 2nd, 2007 18:00

Trying everything, but to no avail on my Dimension 8400

I've always owned Dell's ( 6 of them) and have never had a problem I couldn't fix until now. And how it went bad I'll never know. Just unplugged my puter whilest it was shutting down and it hasn't worked since. I tried re-seating the ram... re-seating the vid card...  unplugging and re-plugging the connectors. Resetting the CMOS.. and that's where I'm at now. I can't remember what PIN is number 1. With all the screwing around with the system, I can't remember what is the normal position for the cmos jumper. Is the number 1 pin on the left or right?? They're not labeled that I can see. Also, I get a steady green on the power led and 3 green and on amber on the troubleshoot LED's. Then I tried to reset the CMOS and get different lights now and the fan whines like mad.. and it powers up by itself as soon as I put the power cord in. And when I try to shut it off it turns on again by itself. This is killing me!  Please tell me what pin is number 1 on the board for the CMOS. Thanks!
  • mombodog

    2 Intern

    •

    12735 Posts

    321

    0

    Posted May 2nd, 2007 19:00

    Anyone with a Dim 8400, please open the cover and check for this person, it is not in the Dell Doc's anywhere.
     
    While you are waiting for a response, unplug the power cord, hold the power button in for 15 seconds and pull the cmos battery out and leave it out, when you get the proper jumper position, reinsert the battery.
     
    Unplugging power while booted up can have disastrous consequences on a Windows Installation and you may have to reinstall .


    Message Edited by mombodog on 05-02-2007 03:44 PM

    Message Edited by mombodog on 05-02-2007 03:46 PM
  • tim5ny

    42 Posts

    321

    0

    Posted May 2nd, 2007 20:00

    Thanks!  I see the one with the white arrow. I held the power switch for 15 seconds then pulled the battery. The jumper was out at this time also prior to pulling battery. I read your message then put the jumper back first on the two unmarked pins. Then I put the battery back in.... put the vid card back in because i had to remove it to get at the battery. Checked all connections inside... closed it up and plugged it in. Mind you.. I'm at work and just brought the case with me thinking that i would hook it up to the dells we have here.. but the monitors at work have a smaller connector and i forgot to bring my adapter. So I unplugged everything from the back of one of the Dells at work to see if all the indicator lights would be green without any peripherals plugged in.. and it lit up everything green when i started it up. So I figured that my Dell should also show all green if it's working right without anything connected. Here's what I get when I plug in to power. The machine starts all by itself without hitting power switch. The power led stays solid green. The fan whines pretty fast. The LED lights on the back are a steady  amber,amber,green,green. I hear 4 beeps when it starts then a pause... then 2 more. I'm so angry that this could happen by just unplugging it when the it was powering off. If I can get to a screen tomorrow at home I will re-install WinXP if need be, but I don't think I can get to a screen. Is there a way to reset the machine manually back to factory?????
  • tim5ny

    42 Posts

    321

    0

    Posted May 2nd, 2007 20:00

    I  wouldn't mind reinstalling windows at all, but I can't even get it to boot that far. Which cmos pin is number one on the board???  The CMOS pins are not marked and I forgot what position is normal for the jumper. It wont boot anyways.. so saying that if the jumper is wrong it wont boot doesn't help me. Please tell me if number one pin is on the left or right when looking at the motherboard with the cmos jumper closest to me in relation to the rest of the mother board. Thanks!
  • shesagordie

    12 Elder

    •

    46017 Posts

    321

    0

    Posted May 2nd, 2007 20:00

    tim5ny

    The D-8400 CMOS three pin setting, is the jumper on the pin marked with a white arrow and the middle pin, this is the clear CMOS setting.

    The normal setting is the jumper on the two unmarked pins.

    Bev.





    ===================================================
    Please don't send me questions about your system by DCF Messenger.
    Post the issue in the appropriate Board, where they will be answered.
  • tim5ny

    42 Posts

    321

    0

    Posted May 2nd, 2007 21:00

    I have 4- 512 ram modules. When I put any one of them in alone it seems to start good except that there's still amber,amber,amber,green. Same results using any of the 4 modules. When I put any two modules in or three, or four I get a loud whining fan, and amber,amber,green,green. They can't all be bad modules I wouldn't think. Why do I get different lights with any one module in than I get with any two, three, or four modules in??


    Message Edited by tim5ny on 05-02-2007 05:47 PM
  • mombodog

    2 Intern

    •

    12735 Posts

    321

    0

    Posted May 2nd, 2007 21:00

    Amber, Amber, Green, Green,  means a memory module has failed, if there is more than one, remove one and try again, if no joy, try the one you removed.
     
     


    Message Edited by mombodog on 05-02-2007 05:31 PM
  • mombodog

    2 Intern

    •

    12735 Posts

    321

    0

    Posted May 2nd, 2007 21:00

    you said amber, amber, green, green?  now its amber, amber, amber, green?
     
    The lights are labeled  A  B  C  D, be sure you give us the correct colors starting with A


    Message Edited by mombodog on 05-02-2007 05:56 PM
  • tim5ny

    42 Posts

    321

    0

    Posted May 2nd, 2007 22:00

    I'm getting different lights everytime I do something different. With ANY one ram module in it's green,green,green, amber.  With ANY two or more in it's amber,amber,green.green.. and it whines(the fan) and turns on without hitting power.. and wont shut off unless i unplug it. With any one ram in it will shut off normal.. turn on normal.. but I get green,green,green,amber with one ram in.


    Message Edited by tim5ny on 05-02-2007 06:22 PM
  • Mary G

    6 Operator

    •

    20095 Posts

    321

    0

    Posted May 4th, 2007 21:00

    This might not apply, but there was a defect in the Dim 8400's that caused the capacitors to fail. Look at the motherboard' capacitors that look like small tin cans and see if the tops are bulging on any of them. If so, contact Dell. This is a repair that Dell was fixing even if out of warranty.
  • mombodog

    2 Intern

    •

    12735 Posts

    378

    0

    Posted May 4th, 2007 21:00

    Mary G, you remember everything.  :smileyhappy:
     
    http://motherboardrepair.com/  check out the images section on the left side.