
UNSOLVED
My Dell Precision 670 turn off automatically
My Dell Precison 670 is running with 2 CPU 3.4 GHz and Windows XP SP2. From last week, after booting into Windows XP about 15 minutes, it turns off automatically and cannot come back running. When it goes to this status: the monitor is all black, the power button is still light and 4 signal led: A (BLUE) - B (YELLOW) - C (YELLOW) - D (OFF)
I cannot do anything when it goes into this status. Only one thing to do is unplug the power cable and re plug it to reboot.
Responses (6)
Solutions (0)
- My Precision 670 doesn't turn off completely, I think that it's just power off because I still see the power light on.As I read in Code Error of Dell manuals. Maybe the VRM has problem but I don't have another machine to try to test before replacing it.I've tryed to reinstall Windows XP and the problem is the same so I don't think the problem comes from software.One more thing, after mine dell went into this status, I unpluged the power and replug again. Right now the machine rebooted but the noise comes from fans is very loudly.
Sam Waring
170 Posts
213
0
Posted June 13th, 2007 11:00
@ncbinh wrote:
My Precision 670 doesn't turn off completely, I think that it's just power off because I still see the power light on.As I read in Code Error of Dell manuals. Maybe the VRM has problem but I don't have another machine to try to test before replacing it.I've tryed to reinstall Windows XP and the problem is the same so I don't think the problem comes from software.One more thing, after mine dell went into this status, I unpluged the power and replug again. Right now the machine rebooted but the noise comes from fans is very loudly.
And that's not surprising in the least. What happens is that the BIOS hangs during the POST process just after issuing the command where it tells the system fans "run very fast for a minute to blow out the stale air from the case" but before it issues the command "OK, you can stop now." Hence, the fans keep running at full throttle. It's a classic no-POST indicator.
Now as far as what's really wrong: Your GYY-OFF quad pack says that the integrated voltage regulator (VRD) for processor 0 has failed and because the VRD is integrated, the only remedy is to replace the motherboard. Doing hardware swaps of VRM1 would be nugacious anyhow, because that's not the voltage regulator which has failed.- I've used Dell Diag to check my Dell Precision 670 but I didn't see any problem.One more thing on my machine: When it goes to "Sleep" status, the monitor is on black about 5 minutes and after that Windows will reboot and it comes back to logon Windows.I'm not sure, should I have to replace a new motherboard? My machine is running with 2 CPU 3.4 GHz and the mortherboard is X0392. Can I buy a Dell Precision 670 with another code or I have to buy exactly the X0392 motherboard?
Sam Waring
170 Posts
213
0
Posted June 19th, 2007 11:00
@ncbinh wrote:
One more thing on my machine: When it goes to "Sleep" status, the monitor is on black about 5 minutes and after that Windows will reboot and it comes back to logon Windows.I'm not sure, should I have to replace a new motherboard? My machine is running with 2 CPU 3.4 GHz and the motherboard is X0392. Can I buy a Dell Precision 670 with another code or I have to buy exactly the X0392 motherboard?
You have two questions run together here. First, the new symptom you report isn't surprising. Everything you've said, to my mind, points back to a dying VRD that's allowing voltage spikes and sags to get past it to the processor. Spikes and sags can certainly cause reboots and no-POSTs such as you describe.
Second, yes, you're locked into that board. Given its part number, you have either Nocona or Irwindale processors and X0392 is the only board used in the 670 that supported those processors. The other 670 board (XC837) is for Paxville processors.

The-wild-wild-w
9 Posts
213
0
Posted June 12th, 2007 05:00