UNSOLVED

ikke_nl

updated

17 years ago

I

ikke_nl

4 Posts

0

19083

August 30th, 2009 06:00

Error after replacing CPU fan optiplex GX150

Hi,

I have recieved a optiplex GX150 with a defective fan. After replacing the fan (and the heatsink) I get a error: "Alert! Systen fan not detected". In the event logs of the BIOS it reads "Out of range CPU #0 fan". This error is shown everytime I reboot the computer.

I have replaced the old one with a "CMP-COOLER22 KÖNIG AMD/INTEL COOLER" Rated speed: 2500±10% RPM .
I do not know the specifications of the old fan.

Since I had to use the old connector because the standard connector is different than the GX150s, What could be the problem:
- The connector is not connecting properly
- The fan is too slow
- The fan is too fast

Does someone have the specifications of the old one? Is de RPM pin also open-collector?

Thanks in advance for replying.

Best of regards.

  • fireberd

    11 Legend

    •

    33399 Posts

    •

    112848 Points

    531

    0

    Posted August 30th, 2009 07:00

    Dell uses a proprietary fan that has additional electronics that is "seen" by the BIOS.  If you install a non-Dell fan it will give you the errors you are seeing.  The only way to eliminate the error is to use another Dell fan.

    Inspiron 16 5630 Laptop and WD22TB4 Docking Station
    Self-built desktop for recording studio application
  • Davet50

    6 Operator

    •

    14442 Posts

    531

    0

    Posted August 30th, 2009 07:00

    you will get that error if you do not use a Dell fan. Dell uses a proprietary fan connection and after market fans will cause this error

  • ikke_nl

    4 Posts

    531

    0

    Posted September 6th, 2009 04:00

    Do you perhaps know what the schematic is of such a fan?

    Perhaps with a small PCB the standard signal can be converted to match a proprietary fan signal.

     

     

  • D.Lewis

    23 Posts

    531

    0

    Posted September 6th, 2009 12:00

    Can I just ask, does this mean that the PC will not boot AT ALL, or just that an error message is displayed on POST?

    I read on another forum that if a BIOS setting - "Do Not Display Keyboard Errors" is set as < Do Not Display> then the error message is skipped, but that the fan itself is not monitored for potential failure.

    Can anyone confirm?

  • ikke_nl

    4 Posts

    531

    0

    Posted September 6th, 2009 15:00

     

    No, it gives a warning and a  "Press F1 to continue, F2 for setup" after the POST.

    It is just annoying, especially for someone with 'beginners' experience with computers. The computer belongs to someone who just finished the senior course Word. I have to experiment with the skip errors option. Skipping errors does not have my preference.

  • Davet50

    6 Operator

    •

    14442 Posts

    531

    0

    Posted September 6th, 2009 15:00

    you can only clear the error by replacing the fan with a dell Fan. Like fireberd mentioned earlier Dell uses a sense lead internal to the fan to check for a fan

  • ikke_nl

    4 Posts

    531

    0

    Posted September 7th, 2009 12:00

    I have to disagree on that point. If the technology in such a fan is that good, why is it only used by one company?

    It has to have some advantages above the 'normal' fans, otherwise why implement it?

     

    By the way, thanks for your tip, but your reply does not answer my question: Does anyone have the schematic of a proprietary fan?

     

     

  • 531

    0

    Posted September 7th, 2009 13:00

    Here's one for less than $20.

    http://www.laptopserviceparts.com/products/DELL/REF/3110KL04WB66.html

    and new...

    http://www.ezsystems.com/newcart/dsku.php?g=3110KL04WB66&m=NMB+Technologies&c=REF

    you may need to configure the 3 leads correctly to match the original plug as follows: on the flat side of the plug the colors are black, red white.

    the extra lead is for the tach reading as these mainboards report fan speed and unlike others this reading is not adjustable by the user.

     

    Good luck!

  • 531

    0

    Posted September 7th, 2009 13:00

    Here's one for less than $20.

    http://www.laptopserviceparts.com/products/DELL/REF/3110KL04WB66.html

    and new...

    http://www.ezsystems.com/newcart/dsku.php?g=3110KL04WB66&m=NMB+Technologies&c=REF

    you may need to configure the 3 leads correctly to match the original plug as follows: on the flat side of the plug with the wires at the top the colors are black, red white.

    the extra lead is for the tach reading as these mainboards report fan speed and unlike others this reading is not adjustable by the user.

     

    Good luck!