
UNSOLVED
Dell Dimension 9200 (XPS 410) won't boot - dead?
5 year warranty but it's 5 y 11 months unfortunately >:(
Specs: 2007 Dell Dimension 9200 (XPS 410 in US), Q6600 quad core, 4 GB RAM, 320 GB HD, Windows Vista, PCI-E x16 256 MB 8600GT graphics, PCI-E x1 tv tuner card (not in use), 22" Dell LCD monitor.
Brief history and prob: weird, early on the hard drive would access every 1 second for a few years, never did figure that out. 2011 Major problem won't boot, fan on max, diagnostic light code that turned out to be meaningless... surprisingly reseating graphics card helped a bit and made pc useable again... errors slowly became less severe, it was weird. they tried to say it was software problem but this seems unlikely since restoring to factory condition (and losing some data) hadn't helped at all. Next two years ok. Two days ago it didn't start right and required a couple reboots. Found it this morning frozen on black Microsoft screen and had to hold power down to turn off. (woke itself for a windows update then died??) Tried to boot but it froze on the very start of the BIOS setup screen, no keyboard no nothing, and got the same old "123" diagnostic code but again there's no such code. Repeated multiple times. Tried reseating video card about ten times, including removing tv card since its not in use - no dice and now diagnostic light code "34" is for possible expansion card failure (not graphics card... but there are no other cards so it must be the graphics card.) No monitor picture at all now...
Cruising dell forums seems to indict 9200 motherboard...
Could try resetting CMOS jumper?
I wish dell had fixed this when it was in warranty.
Any ideas? I don't have another PCI-E PC or graphics card to cross check... worth buying another graphics card to try? Want to save pc if possible. Thanks.
Responses (9)
Solutions (0)
shesagordie
12 Elder
•
46017 Posts
1644
0
Posted July 17th, 2013 13:00
vitaminj
Is the power button LED, solid green, blinking green, solid amber, blinking amber, or off?
Are there any 'Beeps'?
Check the reading of Diagnostic Lights on the front panel?
The Dimension 9200 Troubleshooter and Diagnostic Guide, is HERE. <ADMIN NOTE: Broken link has been removed from this post by Dell>
Bev.
shesagordie
12 Elder
•
46017 Posts
1644
0
Posted July 17th, 2013 13:00
vitaminj
Quote:
"and got the same old "123" diagnostic code but again there's no such code"
There is a 1-2-3-X Diagnostic light code listed, that indicates 'Another failure has occurred', this could be a motherboard, or a hard drive failure.
Bev.
Aargh, checking the online manual, you are right, white means not lit and dark means lit! how stupid! Pretty sure the tech I spoke with in 2011 did not know that. so 3, 4 means memory failure and 123 means other failure. I will try the pairs of RAM tomorrow and see what happens.
shesagordie
12 Elder
•
46017 Posts
1644
0
Posted July 17th, 2013 15:00
vitaminj
If removing and reinstalling the memory modules, does not resolve the issue, try the following:
Remove all the memory modules, then install only one module in slot 1 and see if the system boots and if the computer starts normally, reinstall an additional module.
Does not boot, move the module to slot 2 and again see if the system boots, no boot, try the module in slot 3, no boot, try installing in slot 4.
Still does not boot, then remove the first module and using the second one, repeat the sequence described above.
Still no boot, try installing any remaining modules, one at a time, using the above procedure.
Continue until you have identified any faulty module [or slot] or reinstalled all modules without error.Then if the computer still does not start, it's possible that the motherboard has failed and needs to be replaced.
Bev.Hello Bev,
the power button LED is solid green so there's power but that's about all there is. It kind of beeps but there's no pattern, believe it or not... its kind of randomly spaced - and sickly, warbles more than it should.
Hm, am i misreading the codes? According to my 9200 manual p68 XXX4 is another failure has occurred... p65 says "all four diagnostic lights display solid green and then turn off after the system successfully boots" ... I took this to mean white means lit and dark mean not lit... is it the opposite?
Expected to go through all the combinations and end up with a bad mobo, but just reseating RAM worked! Also noted one of my pairs of RAM does not match perfectly, same brand and specs but one from the US and one from asia, and they do not quite look the same... But it beeped once on startup, ran startup repair, had to reboot a few times, windows came up, it took a hideously long time to shut down again (about a half hour) worrying me a bit. Hard drive sounds scrapey but im prolly just paranoid. RIght now it seems about normal! You solved a 2 year mystery and maybe a 6 year one. Basically you are smarter than Dell. thank you soooooo much Bev. I wonder how many poor folk (and support techs) have been fooled by the stupid manual having grey mean lit and white mean not lit, grr. Noted in my manual. Thanks again very much.
shesagordie
12 Elder
•
46017 Posts
1644
0
Posted July 19th, 2013 11:00
vitamin
Happy to have helped and please to hear the issue is resolved.
Bev.
I had the same problem I replaced the power pack and motherboard. The old power pack sent a high voltage charge to mother board and fried the board. After installing power pack and motherboard the computer would not start. Check your wiring there 2 plugs that are the same. I had them plugged in the wrong place. All I did was switch the plugs and the computer fired up. I don’t know if that’s your problem but it’s worth checking.

DELL-Sundeep B
1 Rookie
•
874 Posts
1644
0
Posted July 17th, 2013 13:00
Hi vitaminj,
Diagnostic indicators "34" indicates a possible memory issue. You may try reseating the memory and see if it helps.
For step by step instructions on adding/removing parts, you may refer to Service Manual Here.
Note : Please follow the safety instructions in manual before removing/installing parts.
If the issue persists, you may try installing one memory in one slot at a time to identify the faulty memory/slot.
Hope this helps.