
UNSOLVED
Copying files to external USB HD
I have the Dimension 9100 STILL with the original A01 BIOS (when will there be a new one?). I am using a 400GB LaCie triple interface external hard drive.
I attach it to the front or rear USB ports, and I am getting consistent 'Delayed Write Failed' messages when copying even small amounts of data to it. It starts to copy files, then it pauses, the 'estimated time remaining' starts to grow, and the machine locks up. A bit later, I get several Delayed Write Failed messages and I have to wait awhile for it to respond again. I have tried both Optimize for Quick Removal and Optimize for Performance on the properties tab of the LaCie device in Device Manager. Same result on both settings.
I have used this same LaCie drive at work on several different machines with no problems. Plus, I thought I saw on an eBay auction for another external HD that they would not guarantee compatibility with Dell systems because most Dell USB ports or controllers don't work well or are not compatible with these external drives. Can anyone attest to that?
What can I do to fix this?
Thank you!
Michael
I attach it to the front or rear USB ports, and I am getting consistent 'Delayed Write Failed' messages when copying even small amounts of data to it. It starts to copy files, then it pauses, the 'estimated time remaining' starts to grow, and the machine locks up. A bit later, I get several Delayed Write Failed messages and I have to wait awhile for it to respond again. I have tried both Optimize for Quick Removal and Optimize for Performance on the properties tab of the LaCie device in Device Manager. Same result on both settings.
I have used this same LaCie drive at work on several different machines with no problems. Plus, I thought I saw on an eBay auction for another external HD that they would not guarantee compatibility with Dell systems because most Dell USB ports or controllers don't work well or are not compatible with these external drives. Can anyone attest to that?
What can I do to fix this?
Thank you!
Michael
Responses (33)
Solutions (0)
- Unbelievable!
I have a 1394 interface off the Audigy ZS 2, so I plugged it in, turned on the drive, and Device Manager shows the device, but Explorer acts funny. If I try to go to Disk Management, it hangs, trying to apparently read the drive! What the heck is wrong with this system or this drive??
Any other ideas???
Michael Hi Michael!
I don't know which LaCie you are running on a 9100, but we run several models from LaCie and others on them without issue and I personally run a d2 Extreme on my home 9100. I doubt your problem is BIOS related, but more likely you need to disable the write caching on that drive given the size. Microsoft has indicated that this occurs with portable external hard drives 60Gb and above, but we've experience on lesser. Good luck!
- Well, I had already had the setting set to Quick Removal. That didn't help. I never had the option for Write Caching, so I assumed it's not turned on.
And, like I said, the firewire option is worse. I can't even get Disk Management to show the device when I plug it in or turn it on. It just hangs DM.
What else can I reset or check to make this drive work?
Michael - Go into Device Manager, open Properties for the USB drive and click the Policies tab. Uncheck 'enable write caching on the disk'. And select optimize for quick removal, too. That should stop the Delayed Write Failed messages.
DWF messages occur when write caching is enabled on some (most?) USB hard drives and they can even make the drive disappear from Windows Explorer even though it's listed in Device Manager as "working properly". If you're curious, there was a knowledge base article on this at microsoft.com.
RonMessage Edited by RoHe on 10-30-2005 06:15 PM
Michael,
We might benefit then from some information about your specific LaCie unit - model and firmware revision in particular. Some of the LaCie units had a firmware update mid-05 to correct communication issues. Also, what particular OS are you running on your 9100? Home, Pro, MCE? Write caching is on by default with all three of these varients of XP if memory serves accurately for Home...
- Write caching is on by default. Here's that knowledge base article from Microsoft which may help you, if turning off write caching doesn't fix it. It includes a possible registry edit to change the number of System Pages enabled at boot up.
http://support.microsoft.com/?kbid=330174&sd=RMVP
Ron

europa303
1 Rookie
•
4428 Posts
930
0
Posted October 30th, 2005 17:00