Dell gave me Latitude 3190 as a replacement for an old Dell Tablet that went bad because they no longer made that tablet. It is running Windows 10 Pro, x64. Have had it for several years now and has worked well as I only use it when traveling.
It shipped supposedly with only a 64GB eMMC drive but manual showed it also has one M.2 slot. Upon opening the computer I found there was already a M.2 2280 64 GB SSD installed. I was confused so contacted Dell. They basically said on some models (ex. Inspiron 3452) they have an eMMC that is mounted on a card and inserted in a slot. So that is what they suspected this is as the actual order for this Latitude 3190 “does not” show it shipped with a M.2 2280 SSD. It only shows it shipped with 64 GB of eMMC.
Because of the small Drive, I only installed a few things on it like Microsoft Office, my Virus software and a small program from Canon for my camera. I keep no files on it at all. No photos, documents, videos, etc. Everything is stored on a large USB Flash Drive.
Always had at least 9-10 GB of free space.
NOW
After many Windows and Dell updates that 64 GB now only shows 4.25 GB free and is in the Red when you view it so decided I would put in a larger M.2 SSD. The max on this Latitude 3190 is 256 GB according to the documentation which is fine. Dell told me which one to buy. What was strange again, was the one they told me to buy and they show under parts for this laptop is an M.2 2230 (the shorter drive). They said there should be a second mounting hole under the current M.2 2280 drive for the M.2 2230. I said fine.
So I bought the M.2 2230, 256 GB Drive they recommended. Bought an extender incase there is not another screw hole under the existing longer 2280 card and bought a USB to M.2 adapter so I could clone it.
My questions
. Should I be able to just clone the current M.2 2280 64 GB drive over to the new M.2 2230 256 GB drive then pull out the old and put in the new and will be good to go?
I was also originally planning to use the SupportAssist OS Recovery from the F12 boot to clone it. I checked it several months ago and it was an option in the menu and went through the procedure. See pic. However, I looked yesterday before starting this project and that option is now gone. See pic.
Don’t know why it is gone considering when I ran Support Assist yesterday it actually updated the SupportAssist OS Recovery to a new version? See Pic. Confused as to why it is gone now when using F12 to boot in BIOS.
Anyway, what good cloning software should I try to use since the SupportAssist OS Recovery seems to be gone now so cannot run it manually?
Oh and the reason for some of the confusion on the M.2 2280 vs 2230 was due to this.
Here is a pic from the manual. It shows an M.2 2280. I then opened the back and this is what is installed. An M.2 2280. But Dell claims there is a second screw hole under there first the shorter 2230.
I have the exact problem. But i am not technical savvy like you so i need help to have clarity in selecting the replacement memory module. The module that is plugged into the socket is 64GB but the key is on the left side which makes it a B key. As i googled to find a replacement with a higher memory, the result are keys (notch) on both side meaning both B + M keys or M only key. To further the difficulties in understanding, the result from google has more technical jargon like SSD, Nvme which makes it more difficult for me to get a replacement with higher memories. Please Help. Thanks in advance.
@Jaydeen I believe I did another post on this when I was done. Yes, after much research I got the M.2 “2280” SATA Version of this drive below in 256 GB since the manual says this is the maximum. It had both the B+M Keys.
ORICO M.2 2280 SATA SSD, 256GB Internal M.2 SSD with B+M Key for Desktop/Laptop, SATA III 6Gbps NGFF Solid State Drive Low Power Consumption (PCIe NVMe Incompatible) - Y20M https://a.co/d/0hUtt2T0
This was the adapter I used in the laptop to clone it. At the end of the cloning it asked a question, I forget what? But basically it was if you want to kinda close the drive at the end to use elsewhere. You need to tell it no.
ELUTENG M.2 to USB Adapter Dual Protocol M.2 NVME SATA Hard Drive USB3.1 Gen2 10Gbps USB to NVME PCI-E SSD Reader M Key & B+M Key Max 4TB Support UASP for 2280 2260 2242 2230 SSD Enclosure https://a.co/d/07VWJtB7
The software I used was the free version of EaseUS Disk Copy.
I then even updated to Windows 11 several months later. Been a year now and all is good. Currently 164 GB Free of the 256 GB.
i did not find the Orico brand in 256GB but i found:
Timetec 256GB SSD 3D NAND SATA III 6Gb/s M.2 2280 NGFF 128TBW Read Speed Up to 550MB/s SLC Cache Performance Boost Internal Solid State Drive for PC Computer Laptop and Desktop (256GB).
@Jaydeen Yes that should work. Any drive like that, that is SATA and not NVMe which works over the PCIe interface should work.
Its been a while but I think the manual said a PCIe would work and there is a setting in the BIOS (that I saw) to switch it but did not want to take the chance as I was fairly new to this too.
If it was a matter of adding an “extra” drive I might have tried it. But since I was cloning and removing the bootable only drive and replacing I played it safe.
I believe I wrote up the full directions on what I did. I will look for them.
Ph and on reboot with the new drive in the BIOS came up and wanted to do some sort of scan or something. I thought oh, something not working? But after that it shut down and rebooted to the picture login screen.
I have cloned the drive look at the map of both the original drives (0) and (1) in the sofware and they resembled in contents. I replace the drives and it took me to testing hardware. After completion of test it shut down, it says no deffect found. I exit and it repeat to reperform hardware test. I exit and pressed F2, it says no booth device found.
@Jaydeen That is what mine did, that hardware scan or whatever after replacing. I think it did it twice also. But after that it just booted to the login screen.
When you first put the empty new drive in the adapter and plugged it in, your computer should not have recognized it. I finally found my full write up, it was on my other computer and I had to go to Computer Management and initialize it first as a New Simple Volume first.
The computer also would not let me eject it the normal way after it was cloned. I think it was because the USB adapter was still being detected as in use? Did you also get the message about NOT booting from it when in the adapter plugged into the USB Port?
I can't attach a .pdf file of my notes. Let me take some screen shots and attach them.
Thanks. Let me see if it will let me attach the 9 screenshots on exactly what I did? I am fairly good with some of this stuff but this is the first time I ever cloned a drive. All I can think is start over. Make sure to wipe the new one so it is back to the state it was when it shipped as an uninitialized drive.
jsuvman
2 Intern
•
35 Posts
•
5 Points
0
0
Posted February 24th, 2025 12:40
Oh and the reason for some of the confusion on the M.2 2280 vs 2230 was due to this.
Here is a pic from the manual. It shows an M.2 2280. I then opened the back and this is what is installed. An M.2 2280. But Dell claims there is a second screw hole under there first the shorter 2230.