
解決済み!
解決策へ移動Data Domain:コンプライアンスモードのiDRACユーザー作成について
コンプライアンスモードの導入を予定しています。
CLIで system retention-lock compliance configure を実行後に
CLIで iDRAC ユーザーを作成を考えています。
オペレータ権限ユーザー:2 → 例:idrac-ope-1、idrac-ope2
読み取り権限:2 → 例:idrac-ro-1、idrac-ro-2
確認
CLIにて上記の権限毎のユーザー作成するにはどうすればよいのでしょうか。
CLIでは user idrac createとなっており、これで権限をどのように付与するのか
不明でした。
どうぞよろしくお願い致します。
返信(2)
解決策(0)

ayas
Community Manager
•
7537 投稿
•
68231 ポイント
0
0
投稿済み 2026年11月12日 02:08
RB-7716さん
オペレータ権限ユーザー:2 → 例:idrac-ope-1、idrac-ope2
読み取り権限:2 → 例:idrac-ro-1、idrac-ro-2
CLIにて上記の権限毎のユーザー作成するにはどうすればよいのでしょうか。
CLIでは user idrac createとなっており、これで権限をどのように付与するのか
→user idrac create コマンドは引数を取らないコマンドのため(help 実行時に “this command does not take any arguments” と表示されます)、オプションで権限を指定することはできません。
コマンドを実行すると対話形式で設定が進み、「オペレータアカウント数」「読み取り専用アカウント数」を入力したあと、それぞれの枠でユーザー名とパスワードを入力します。権限を付与というよりもどのユーザをどの権限にするか、という感じで設定することになります。
実際のコマンド例)この例ではアカウント数はそれぞれ1なのでRB-7716さんの場合は2が必要になります。
# user idrac create
** Run this command only if you intend to enable retention-lock compliance mode on this system. It will disable access to the iDRAC "root" account and delete all the other existing iDRAC user accounts.
At most 13 accounts can be created. At least one account must be an iDRAC operator.
All other accounts may be iDRAC operators or readonly users.
The iDRAC operator accounts will be disabled and readonly accounts will be enabled by default.
Do you want to continue? (yes|no) [no]: yes
This command requires authorization by a user having a 'security' role.
Please present credentials for such a user below.
Username: XXXXXX
Password:
Enter the number of iDRAC operator accounts to be created: 1
Enter the number of iDRAC readonly accounts to be created: 1
iDRAC operator user 1:
Enter username: XXXXXXX
Enter new password:
Re-enter new password:
Passwords matched.
iDRAC readonly user 1:
Enter username: XXXXXX
Enter new password:
Re-enter new password:
Passwords matched.
参考情報
Dell EMC Knowledge Article 000427580 : Data Domain: How to enable compliance or governance on Data Domain (大まかな流れ)
Helpコマンドした時の出力
sysadmin@dd3300-FF28# user idrac create help
**** Syntax error - this command does not take any arguments.