UNSOLVED

WheelerDK

updated

2 years ago

W

WheelerDK

1 Rookie

•

4 Posts

0

10207

December 31st, 2019 06:00

CPU 2 VCCIO PG voltage is outside of range

I have a new PowerEdge T640 with a Xeon Silver 4110 and it works fine but ever time I put CPU 2 in the socket it will not start and I get the message "cpu 2 vccio pg voltage is outside of range". What is that?

I have try white two diff. CPU (both Xeon Sivler 4110) and get the same error.

Can the standard PSU not power two CPU or?

  • Dell-DylanJ

    6 Operator

    •

    2924 Posts

    5231

    0

    Posted December 31st, 2019 08:00

    VCCIO would refer to the voltage going to the processor pins used for IO, but not memory. With two different processors reporting this, I'd be looking at the motherboard.

    Troibleshooting steps you can try would be: 1) Shutting the server down, unplugging power, then holding the power button for 30 seconds.  2) Flashing your BIOS and iDRAC firmware may help, if they're behind.

    How many watts is your PSU rated for, also? I would expect a different error if that were the source of the problem, but I would appreciate you sharing, just in case.

  • WheelerDK

    1 Rookie

    •

    4 Posts

    5206

    0

    Posted January 1st, 2020 11:00

    The PSU is a 750W standard.

    Shall I try to update BIOS/iDRAC?

  • Dell-DylanJ

    6 Operator

    •

    2924 Posts

    5173

    0

    Posted January 3rd, 2020 08:00

    Yes. I recommend two steps.

    1) Shutting the server off, unplugging it, then holding the power button for 30 seconds, and then

    2) Updating the BIOS and iDRAC

  • WheelerDK

    1 Rookie

    •

    4 Posts

    5071

    0

    Posted January 26th, 2020 01:00

    I have update BIOS to ver. 2.4.8 and IDRAC to ver., 4.

    But I get the same error. Every time CPU 2 is in there is a power fail and with only one CPU it run fine.

  • Dell-DylanJ

    6 Operator

    •

    2924 Posts

    5058

    0

    Posted January 27th, 2020 11:00

    The only other test that I could suggest would be to test the CPUs in another server. If the problems follow the CPUs, then the problem would be there. If they don't then you'd either be looking at the motherboard. I'd expect a different error for insufficient power, but you can test that if you have any larger compatible PSUs on hand.

  • samsut tabris

    1 Rookie

    •

    4 Posts

    0

    0

    Posted November 23rd, 2023 09:43

    i have same issues, i recently swap the prosessor and all working normaly, but if i installed two prossesor i have issue again, help me 

    DELL-Erman O

    Moderator

    •

    2984 Posts

    •

    14874 Points

    0

    November 23rd, 2023 11:07

    Hi, you can try updating iDRAC and BIOS. I advised you to clear old SEL(system event logs) in iDRAC. Don't forget the CPLD version update. The CPLD update had fixes for some voltage problems.
    Perform a power drain. 
    1- switch OFF the server
    2- remove both power supply cables
    3- press and hold the power button for 30 seconds
    4- connect back the power cables and then power ON the server
    5- get into BIOS, select iDRAC settings, go to system logs and clear all the previous logs

    if you have any larger compatible PSUs on hand, you can test that as well.

  • Leonardo Medina

    1 Rookie

    •

    1 Message

    0

    1

    Posted January 22nd, 2024 19:37

    In my case, replacing the thermal paste on the CPUs solved the issue.

  • spnbill

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    0

    Posted January 1st, 2025 09:46

    @Leonardo Medina​ that worked for me. Thanks for your comment; I had to add more thermal paste. 

  • gdevendra

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    0

    Posted April 7th, 2025 04:53

    Thanks Sir ,

    your answer saved my time.

  • Jose Luis Martinez

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    0

    Posted April 27th, 2025 21:00

    @Leonardo Medina​ hola Leonardo, yo tengo un R440 y voy aprobar a echar pasta… a ver si hay suerte. Muchas gracias por el aporte.