Two Optiplex 7050 PCs have stopped seeing NVMe drives in M.2 slot
I have six Dell Optiplex 7050 PCs. All were supplied at the same time and were fitted with a 1TB HDD as standard, but I installed Samsumg EVO NVMe drives into the M.2 slots for the Windows 10 OS.
All systems have been working fine for years, but two that haven't been used for several months are no longer booting and the NVMe drives are no longer visible in the BIOS. I have done the following:
1. Replaced CMOS backup cells
2. Tried all manner of settings changes in BIOS
3. Tested the NVMe drives in another 7050 and they're both fine
4. Flashed the BIOS anyway even though all PCs were already on the latest version 1.27
What possible reason could there be for these two PCs to be suddenly not seeing the drives in the M.2 slots?
The obvious culprit was the CMOS battery. The date was still correct, but I replaced it anyway. It was down to 2.8V so I was hopeful that this would fix the issue, but it didn't.
Restoring BIOS settings from 'Last good known', 'Factory' and 'Defaults' hasn't worked even though the settings on a working PC work fine with the defaults.
I've also tried all manner of settings including disabling secure boot/enabling legacy, setting SATA to Raid, Disabled etc. Not that I have any reason to think these will be the issue since the working PCs are fine with the BIOS defaults, but I'm completely stumped and just started trying different settings as a last resort.
The drives themselves are fine as they work okay in one of the other PCs, but these show the drive when present in the M.2 slot and the problem PCs don't.
What could possibly cause two working 7050s to stop seeing the drives in their M.2 slots after being left alone for several months?
Of course I've made sure that the drives are properly seated in the M.2 connectors and that the edge connection strips are clean and undamaged.
Is there a way I can print out or list all the BIOS settings to do a thorough comparison between the good and bad PCs?
Well one of the reason could be motherboard degeneration that is not reversed with cmos battery replacement. Reading your report I did not see you mention clearing CMOs. Have you already tried using CLR CMOS jumper to clear CMOs?
I do not recommend playing around w all possible bios settings. Load factory default is imo best way to go for standard functions. Of note if CMOs is corrupted then replacing battery or soft reset of bios settings do not rectify it. It needs a hard reset. Thus recommend the jumper method. At bottom of motherboard near the black pciex16 slot there is a silkscreen instruction table of jumper (service mode, password, cmos). Follow the cmos clear instructions.
@redxps630 Thanks - that fixed the issue on both PCs.
I didn't know about the hard reset and there are some aspects of this procedure that aren't very clear so I'll add some notes for the benefit of anybody else who comes across this.
...no mention of the jumpers and step 2 refers to a 'battery cable'?
In the light of no clear step-by-step instructions, I assumed that the repositioning of the jumper from its default position (3-4) to the reset position (5-6) is a momentary operation - like pressing a reset button, but just in case, I left it for a few minutes before returning it to the default position.
As there's no confirmation that the reset has been done, I then also removed the battery and left it for a minute or two as per the instructions. After replacing the battery, I did the jumper reset again just to be sure.
After this, I powered up into the BIOS settings (I had to reset the system date which confirmed the reset had worked) and I could see that the M.2 slot was showing the drive, so after checking through the settings (some of these were not correct after the reset), I saved and exited to reboot.
All was fine and the PC booted to Windows, but on the second problem machine, I just did the reset using the battery removal method as per the manual without any jumper reset. This also fixed the missing drive problem, but there were fewer changes needed in the BIOS this time confirming that the hard reset with the jumper does, indeed, reset more of the BIOS settings than using the method in the manual.
From this experience it appears that there are three different methods for resetting the BIOS settings (one soft and two hard), all of which have different results with the jumper method resetting the most values.
It's a pity there is no mention of this in the manual, but giving details of the battery removal method rather than the jumper method seems particularly unhelpful.
jumper method clears RTC real time clock and is the most effective way to clear corrupted cmos
when the cmos is healthy working, soft reset bios settings in the bios menu reloads factory default settings. the perquisite of this working is a healthy cmos to begin with. when cmos is corrupted, all bets are off in soft reload.
the cmos battery attempts to maintain settings saved in cmos, whatever that is. a corrupted settings is also maintained. removing battery supposedly drains all power from cmos and leads to spontaneous reload of factory default settings, but by the same explanation above is not as effective as the hard jumper reset.
redxps630
11 Legend
•
16431 Posts
•
83176 Points
0
1
Posted October 21st, 2024 20:23
Well one of the reason could be motherboard degeneration that is not reversed with cmos battery replacement. Reading your report I did not see you mention clearing CMOs. Have you already tried using CLR CMOS jumper to clear CMOs?
I do not recommend playing around w all possible bios settings. Load factory default is imo best way to go for standard functions. Of note if CMOs is corrupted then replacing battery or soft reset of bios settings do not rectify it. It needs a hard reset. Thus recommend the jumper method. At bottom of motherboard near the black pciex16 slot there is a silkscreen instruction table of jumper (service mode, password, cmos). Follow the cmos clear instructions.
(edited)