I am trying to establish contact with this switch using the barest of configs so that I can update to the latest firmware, and of course configure the box using the web interface etc.
SW version 1.0.0.20 (date 10-Dec-2007 time 14:44:08)
Fast Ethernet Ports ========================== no shutdown speed 100 duplex full negotiation flow-control off mdix auto no back-pressure
Gigabit Ethernet Ports ============================= no shutdown speed 1000 duplex full negotiation flow-control off mdix auto no back-pressure
interface vlan 1 interface port-channel 1 - 15
spanning-tree spanning-tree mode STP
qos basic console#
And to no avail - I cannot ping it, it cannot ping me...
console# sh ip int
Gateway IP Address Activity status Type ----------------------- ----------------------- -------- 192.168.3.1 Active static
IP Address I/F Type ----------------------- -------------------- --------- 192.168.3.22/24 vlan 1 Static
console# ping 192.168.3.201 Pinging 192.168.3.201 with 56 bytes of data:
PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout
My PC (192.168.3.201) is connected directly to the switch, and another cable connects the switch into my infrastructure, and my PC can ping anything else I want to...
Pinging 192.168.3.22 with 32 bytes of data: Reply from 192.168.3.201: Destination host unreachable. Reply from 192.168.3.201: Destination host unreachable. Reply from 192.168.3.201: Destination host unreachable. Reply from 192.168.3.201: Destination host unreachable.
Ping statistics for 192.168.3.22: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
C:\Users\donmc>ping cityethics.org
Pinging cityethics.org [192.168.3.5] with 32 bytes of data: Reply from 192.168.3.5: bytes=32 time<1ms TTL=64 Reply from 192.168.3.5: bytes=32 time<1ms TTL=64 Reply from 192.168.3.5: bytes=32 time<1ms TTL=64 Reply from 192.168.3.5: bytes=32 time<1ms TTL=64
Ping statistics for 192.168.3.5: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms
C:\Users\donmc>
Any Suggestions would be most welcome - I am starting to think that the box is faulty...
console# sh ver SW version 1.0.0.20 ( date 10-Dec-2007 time 14:44:08 ) Boot version 1.0.0.08 ( date 29-Nov-2007 time 16:38:01 ) HW version 00.00.02 console# sh bootv Image Filename Version Date Status ----- --------- --------- --------------------- ----------- 1 image-1 1.0.0.20 10-Dec-2007 14:44:08 Not active 2 image-2 1.0.0.20 10-Dec-2007 14:44:08 Active*
"*" designates that the image was selected for the next boot
What is interesting to me is that when I try to PING either FROM or TO the 3524P I can capture the ARP requests going out from the 3524P to get a MAC to send the ping packets to, and I can see the ARP-REPLY being sent from my PC, but the switch never appears to receive the ARP-REPLY, so it never actually sends the PING packet. The reverse is also true - if I ping from the PC to the 3524P I can see the ARPs going out, but no ARP-REPLY coming back.
I would update the firmware if I could, but I am unable to get packets through right now... and I don't want to use XMODEM on a serial port...
I will update this tomorrow and let you know these details (MAC addresses & ARP tables etc. If you can give me the syntax to find out arp addresses for a port, that would help.
It is definitely NOT the cable, as I am getting my network traffic through the same cable with no problem - it is only local management that is failing to connect. Is there any way to attach an image file to these forum entries ? That would be easier for some data.
Remember, the 3524P is at 192.168.3.22, my Windows 7 PC is at 3.201
console# ping 192.168.3.201 Pinging 192.168.3.201 with 56 bytes of data:
PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout
Vlan Name Ports Type Authorization ---- ----------------- --------------------------- ------------ ------------- 1 1 e(1-24),g(1-4),ch(1-15) other Required
Pinging 192.168.3.22 with 32 bytes of data: Reply from 192.168.3.201: Destination host unreachable. Reply from 192.168.3.201: Destination host unreachable. Reply from 192.168.3.201: Destination host unreachable. Reply from 192.168.3.201: Destination host unreachable.
Ping statistics for 192.168.3.22: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss)
And Finally, an image is attached of the Wireshark Packet Capture.
Note that the 3524P does not respond to my PC's ARP requests for a MAC address for 192.168.3.22
Whereas, when the
So that is what is going on.
console# ping 192.168.3.201 Pinging 192.168.3.201 with 56 bytes of data:
PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout PING: no reply from 192.168.3.201 PING: timeout
VLAN Interface IP address HW address status --------------------- --------------- ------------------- ---------------
console# console# console# ping 192.168.3.22 Pinging 192.168.3.22 with 56 bytes of data:
56 bytes from 192.168.3.22: icmp_seq=1. time=0 ms 56 bytes from 192.168.3.22: icmp_seq=2. time=0 ms 56 bytes from 192.168.3.22: icmp_seq=3. time=0 ms 56 bytes from 192.168.3.22: icmp_seq=4. time=0 ms
An update - I have successfully uploaded the new firmware image to the switch, so:
console# sh ver SW version 2.0.0.42 ( date 01-Sep-2010 time 15:26:19 ) Boot version 1.0.0.08 ( date 29-Nov-2007 time 16:38:01 ) HW version 00.00.02 console#
Still NO connectivity via ethernet. I have changed the default VLAN from 1 to 22 just for grins, and it changes nothing.
bh1633
909 Posts
1473
0
Posted November 18th, 2010 12:00
The first thing I would do is update to the latest firmware.
What is the MAC address of the switch and PC in the arp request/replies?
Did you check the cable? It seems like the switch CPU does not receive any of the packets sent from the PC.
Does the switch learn the MAC address of the PC?
What is in the arp tables of the switch and PC?