Problems jukebox "Incompatible Medium" on NW 7.3.2 with SL500, Solaris 8
I have just installed the NW 7.3.2. on Solaris 8. But when I tried inventory nsrjb -I the operation reject. I tried to load the cartridge on tape drive but it also reports the error.
The cartridges are the same type like tape drives LTO2 (Ultrium 2), they are working on stand alone drives, but when i put in library they failed.
What could mean RAP report: Invalid resource data.?
There are barcode labels on tapes.
Please advise, what could cause this problem. See the deamon log:
04/04/08 16:08:46 nsrd: media info: Jukebox `SL500' Hardware status of jukebox 'SL500' is 'ready'
04/04/08 16:09:23 nsrd: [Jukebox `SL500', operation 1]. Initiated operation `operation: "Load"; operation device: "/dev/rmt/2cbn"; operation slots: " 1"; write enabled: "Yes"; '.
04/04/08 16:09:25 nsrlcpd #1: Jukebox error: Jukebox:SL500 access:scsidev@6.100.0 failed:MOVE MEDIUM key:5 status:CHECK CONDITION No Additional Sense, Incompatible Medium Installed
04/04/08 16:09:26 nsrmmgd: lcpd 1 at host mpmvivatel reported error 'Jukebox:SL500 access:scsidev@6.100.0 failed:MOVE MEDIUM key:5 status:CHECK CONDITION No Additional Sense, Incompatible Medium Installed
' for the command `4'.
04/04/08 16:09:26 nsrd: [Jukebox `SL500', operation # 1]. Jukebox:SL500 access:scsidev@6.100.0 failed:MOVE MEDIUM key:5 status:CHECK CONDITION No Additional Sense, Incompatible Medium Installed
04/04/08 16:09:26 nsrmmgd: Jukebox:SL500 access:scsidev@6.100.0 failed:MOVE MEDIUM key:5 status:CHECK CONDITION No Additional Sense, Incompatible Medium Installed
This message is just parsed by NW. In reality this message is sent by library itself. Library is using set of standard signals known as ASC/ASCQ codes and in this case this one is 30h/00h. Library may reports this under different circumstances like having wrong wrong barcodes or media type which does like each other (one such occasion that I'm aware was when Cleaning tape was used by Seagate against IBM drives - CLNS vs CLNI - not that this is your case of course).
I would inspect what you have really in library and its barcodes. If you try the same operation from library panel I believe you will get the same error.
Thanks for information.Myabe the problem is on HW site. I will go on-site and check the library. If this is a message not from NW I will try to look in SL500. But it is stange that at first NW nsrd deamon says : "media info: Jukebox `SL500' Hardware status of jukebox 'SL500' is 'ready'?. Meanwhile the library checks the cartridges by barcodes and then operate with it. If I corectly understood your post. So if I try to make operation with madia with not right barcode I could expect similar error? Thanks for help, when I return back will explain what happens? Have a nice weekend.
When your start NW (and when you configure jukebox) two daemons are spawned and they start monitor library (first step is inventory). When that is done NW will give you the "ready" state (if you already have library configured you can see that via nsrjb command which may tell you library is in ready or no ready state). That state is not parsed by library, but it is triggered by NW itself.
Yes, if barcode is for another media type library may give you that error.
The porblem seems to be more serious. I went on site and saw that there were LTO2 tapes with LTO3 labels. We corrected the mistake but the problem wasn't solve. I reconfigured the jukebox and the then start hte label operations. And it failed. The tape went to the drive and after that it wasn't possible to eject it. Here is the output from daemon.log.
04/11/08 12:36:40 nsrlcpd #1: Starting program `nsrlcpd #1', with process ID 1711, on HOST mpmbackup. 04/11/08 12:36:44 nsrlcpd #1: Creating Jukebox `SL500' 04/11/08 12:36:46 nsrlcpd #1: Configuring Jukebox `SL500' 04/11/08 12:36:51 nsrd: media info: Searching for new backup devices... 04/11/08 12:36:51 nsrd: media info: Searching for NetWorker SCSI devices on 'localhost'... 04/11/08 12:36:51 nsrd: media info: Starting dvdetect process on host 'localhost'... 04/11/08 12:37:01 nsrd: media info: Jukebox `SL500' Hardware status of jukebox 'SL500' is 'ready' 04/11/08 12:38:28 nsrd: media warning: Jukebox `SL500' The jukebox `SL500' detected some change in it port. 04/11/08 12:39:32 nsrd: media info: Jukebox `SL500' Hardware status of jukebox 'SL500' changed from 'export/import port is open' to 'ready' 04/11/08 12:42:53 nsrd: [Jukebox `SL500', operation 1]. Initiated operation `operation: "Deposit"; operation response: "No"; '. 04/11/08 12:45:18 nsrd: [Jukebox `SL500', operation 2]. Initiated operation `operation: "Label"; operation device: "/dev/rmt/2cbn"; operation response: "prompt"; operation slots: "1-1"; operation template: "Bar Code Label"; operation volume pool: "Default"; '. 04/11/08 12:45:53 nsrd: /dev/rmt/2cbn Verify label operation in progress 04/11/08 12:45:53 nsrmmd #1: check_tapealert: check_cdi_infop and cdi_open failed, the device file name specified is unusable by CDI for device /dev/rmt/2cbn Errno indicates : No such device or address 04/11/08 12:45:53 nsrd: media warning: /dev/rmt/2cbn reading: read open error: drive status is 04/11/08 12:45:54 nsrd: /dev/rmt/2cbn Label without mount operation in progress 04/11/08 12:45:54 nsrmmd #1: check_tapealert: check_cdi_infop and cdi_open failed, the device file name specified is unusable by CDI for device /dev/rmt/2cbn Errno indicates : No such device or address 04/11/08 12:45:56 nsrd: [Jukebox `SL500', operation # 1]. Finished with status: retryable 04/11/08 12:45:56 nsrmmgd: RAP error: Invalid resource data. 04/11/08 12:45:56 nsrmmgd: Cannot update operation status resource (instance 1).
04/11/08 12:45:56 nsrd: [Jukebox `SL500', operation # 2]. read open error: drive status is 04/11/08 12:45:56 nsrd: /dev/rmt/2cbn Eject operation in progress 04/11/08 12:45:56 nsrmmd #1: check_tapealert: check_cdi_infop and cdi_open failed, the device file name specified is unusable by CDI for device /dev/rmt/2cbn Errno indicates : No such device or address 04/11/08 12:45:57 nsrlcpd #1: Jukebox error: Jukebox:SL500 access:scsidev@6.100.0 failed:MOVE MEDIUM key:5 status:CHECK CONDITION No Additional Sense, Medium Not Present
I decide that there should be a problem with HW, and do the commands inguire and mt -f status for the drive. It was a big surprise for me! NW find drives and configure the library but the server says the threre's no such device or path. Has anybody know what is the problem?
root@backupmpm# inquire scsidev@1.0.0:FUJITSU MAW3073NCSUN72G 1703|Disk, /dev/rdsk/c0t0d0s2 S/N: 000707B0KBPD DAN0P720KBPD scsidev@1.1.0:FUJITSU MAW3073NCSUN72G 1703|Disk, /dev/rdsk/c0t1d0s2 S/N: 000707B0KBT4 DAN0P720KBT4 scsidev@1.2.0:Sun D240 1.09|Processor, /dev/es/ses0 scsidev@1.3.0:Sun D240 1.09|Processor, /dev/es/ses1 scsidev@1.4.0:HP C7438A ZP5A|Tape, /dev/rmt/0cbn S/N: HU10713RN1 ATNN=HP C7438A HU10713RN1 scsidev@1.6.0:LITE-ON DVDRW SHM-165P6SM-S1|CD-ROM, /dev/rdsk/c0t6d0s2 scsidev@3.0.0:SEAGATE ST373207LSUN72G 045A|Disk, /dev/rdsk/c1t0d0s2 S/N: 5035Z8VM 3KT5Z8VM scsidev@3.1.0:SEAGATE ST373207LSUN72G 045A|Disk, /dev/rdsk/c1t1d0s2 S/N: 5035ZBN9 3KT5ZBN9 scsidev@3.2.0:Sun D240 1.09|Processor, /dev/es/ses2 scsidev@3.3.0:Sun D240 1.09|Processor, /dev/es/ses3 scsidev@3.4.0:HP C7438A ZP5A|Tape, /dev/rmt/1cbn S/N: HU107039EG ATNN=HP C7438A HU107039EG scsidev@3.6.0:LITE-ON DVDRW SHM-165P6SM-S1|CD-ROM, /dev/rdsk/c1t6d0s2 scsidev@4.0.0:HP Ultrium 2-SCSI K541|Tape, /dev/rmt/2cbn S/N: HU10623EY4 ATNN=HP Ultrium 2-SCSI HU10623EY4 WWNN=500104F00094126E WWPN=500104F00094126F PORT=00000001 scsidev@5.1.0:HP Ultrium 2-SCSI K541|Tape, /dev/rmt/3cbn S/N: HU10623EYW ATNN=HP Ultrium 2-SCSI HU10623EYW WWNN=500104F00094126B WWPN=500104F00094126C PORT=00000001 scsidev@6.100.0:STK SL500 1092|Autochanger (Jukebox) S/N: 559000101658 WWPN=500104F000941262 PORT=00000001 root@backupmpm# root@backupmpm# mt -f /dev/rmt/3cbn status /dev/rmt/3cbn: No such device or address root@backupmpm# mt -f /dev/rmt/2cbn status /dev/rmt/2cbn: No such device or address root@backupmpm# Please advise, i think it is a Solaris 8 and E4900 issue, but if you know something about it please help!
When I look at daemon.log one thing that is possible is that order of devices has changed, but then mt check of devices does yield interesting results. inquire finds what exists on the system... it might have been out of cache so to eliminate that do inquire -cl
ble1
6 Operator
•
14354 Posts
•
56186 Points
1347
1
Posted April 4th, 2008 14:00
I would inspect what you have really in library and its barcodes. If you try the same operation from library panel I believe you will get the same error.