UNSOLVED

ak1920

updated

2 months ago

A

ak1920

1 Rookie

•

3 Posts

•

25 Points

0

165

August 25th, 2026 16:39

U2725QE randomly freezes and becomes completely unresponsive – MacBook Pro 16” M3 Max

My Dell U2725QE randomly freezes during normal use with a MacBook Pro 16-inch M3 

Max connected directly via Thunderbolt.

MacOs Tahoe 26.5.1 (25F80).

DDPM latest 2.3.0.1005

When the issue occurs, the screen goes black and the monitor becomes completely unresponsive, including the physical joystick and OSD controls. Disconnecting the Thunderbolt cable from the MacBook does not restore the monitor, and the monitor does not recover on its own.

The only way to recover it is to physically unplug the monitor from AC power and plug it back in.

The issue has occurred multiple times. It initially occurred with firmware M2T101. I have since updated the monitor to M2T102 and performed a full power reset with all cables disconnected, but the issue occurred again.

Dell Display and Peripheral Manager logs show communication/detection failures around the time of the freeze. Examples include:

FATAL Communications Error. Disconnected?

GetDDCCICommand()-FAILS => 4

USB GetServiceTag failed

No USBPassthrough displays available

Can't check connection, DELL U2725QE's displayState is 3

changeStatusIcon from=DDPM-searching to=DDPM-notfound

DDPM detectMonitorConut:0

After disconnecting and reconnecting AC power, the monitor becomes operational and is detected normally again.

Could you please advise whether this is a known firmware/Thunderbolt issue with the U2725QE and MacBook Pro M3 Max, or whether the monitor has a hardware fault and should be replaced under warranty?

I can provide the complete DDPM Diagnostic Report if required.

I have the complete DDPM Diagnostic Report available. Please contact me by email if you need the full diagnostic logs for further investigation.

(edited)

  • ak1920

    1 Rookie

    •

    3 Posts

    •

    25 Points

    8

    0

    Posted September 2nd, 2026 13:07

    Hello! Some updates? 

  • ak1920

    1 Rookie

    •

    3 Posts

    •

    25 Points

    6

    0

    Posted September 8th, 2026 19:19

    Hello,

    I would like to add some additional diagnostic information to my existing support case.

    The issue occurred again today, September 8, at approximately 17:26. The monitor suddenly disconnected during normal use and entered its built-in self-diagnostic mode. I had to physically disconnect and reconnect the display connection to restore normal operation.

    I am attaching a redacted extract from the Dell Display and Peripheral Manager diagnostic log covering the 17:00–18:00 period.

    The log appears to capture the incident. Around 17:26, DDPM reports a DDC/CI timeout followed by multiple communication errors, including:

    “Unable to read back value after 100 x 100ms for VCP 0xFE”

    “FATAL Communications Error. Disconnected?”

    Shortly afterwards, DDPM disconnects the monitor and then detects it again.

    The timing corresponds to the issue I observed with the monitor.

    I hope this additional log information will help with the investigation. I can also provide the complete DDPM diagnostic report if needed.

     

    1 Attachment

  • DELL-ChrisM2

    Community Manager

    •

    2007 Posts

    •

    10044 Points

    5

    0

    Posted September 8th, 2026 19:50

    Great troubleshooting!

     

    * Click the blue "Get Help Now" on the right to start a private live chat session. Share the private Service Tag with them so that they can verify the ownership and warranty. Also share the link to this Forum thread to enable them to read the issue and your troubleshooting. You will send them the DDPM diagnostic data

     

    * Do you have Windows OS computer with USB-C there to replicate the issue?

     

     * Did you post the issue on the Apple Forum to see if other U2725QE have same issue and what troubleshooting they can offer?

     

    #IWork4Dell