UNSOLVED

The Enigmatic

updated

20 years ago

0

26472

March 1st, 2007 22:00

For those of us who have purchased a rev. A03 2407 in the past few months...

and who want 1:1 pixel mapping, is there any way at all to get an exchange up to a rev. A04?
  • DELL-Chris M

    Community Manager

    •

    56891 Posts

    •

    232143 Points

    436

    0

    Posted March 1st, 2007 22:00

    The Enigmatic,

    You must prove that with your existing gaming setup, (PS3, Xbox360, etc.), your sending a signal (Fill) to the monitor that is not producing the (Wide) 1:1 pixel mapping.


    DELL-Chris M (old account)

    #IWork4Dell

  • 436

    0

    Posted March 1st, 2007 22:00

    Oh that's quite doable. Are some pictures of the X360 (via VGA cable) set at 1920x1080 in the display menu with the 2407's OSD showing greyed out settings for 1:1 valid? And if so, how shall I go about the exchange process? The customer service phoneline?
  • DELL-Chris M

    Community Manager

    •

    56891 Posts

    •

    232143 Points

    436

    0

    Posted March 2nd, 2007 20:00

    The Enigmatic,

    That is valid. Post them on this thread.

    Technical Support (Chat, Email, and Phone)


    DELL-Chris M (old account)

    #IWork4Dell

  • 436

    0

    Posted March 3rd, 2007 15:00

    Here they are, not only is Wide Mode greyed out, it's clear that the image is stretched to fill the entire screen.

    Free Image Hosting at www.ImageShack.us

    Free Image Hosting at www.ImageShack.us

    And when I call Tech Support, I should refer them to this thread as proof and it should be sufficient to procure an exchange?

    Message Edited by The Enigmatic on 03-03-2007 11:26 AM
  • 436

    0

    Posted March 5th, 2007 19:00

    I would like to clear up some stuff before I go to tech support. What will I need to have with me in order to authorize the exchange? You said the pictures were proof enough of the monitor's defect, the inability to display with the proper aspect ratio. Do I need a service tag? And where would I find this service tag if so? The website only points out locations for LCD/Plasma TV's, not monitors. I just want to be ready with the proper things.
  • 436

    0

    Posted March 5th, 2007 22:00

    Why didn't this get bumped...?
  • winnieB

    2 Intern

    •

    1058 Posts

    436

    0

    Posted March 6th, 2007 22:00

    so did you get your monitor exchanged?
     
     
    XPS 410
    Pentium C2D E6700 2.66
    2 GB @ 667mzh (2 dimms)
    Dual 80GB Raptors @ 10,000 RPM in RAID 0 (silenced)
    320GB hdd
    160GB hdd
    NVIDIA 7900GS Zalman VF-900cu
    ATI TV Wonder 650 HD
    Diamond 24-bit 7.1 surround, w/ dolby digital live
    2407 & 2001 monitors
    logitech G7 mouse, G15 keyboard

    ----------------------------------"GAME ON"-------------------------------
  • Buckchoi

    12 Posts

    436

    0

    Posted March 7th, 2007 06:00

    Hi Chris,
     
    I live in New Zealand and own a 2407WFP A02 purchased mid last year. I previously had an A01 which was replaced via sending you a PM with required details, because of the banding issue. (much appreciated thanks!)
     
    I have had no problems with this monitor using it at native resolution, until I got my hands on a Xbox360.
    I too am experiencing this issue. I am currently borrowing a friends Xbox360, and I am purchasing a PS3 when they are released here at the end of the month. (so hopefully would like to get this sorted before then).
    1080p mode cannot be set as 1:1 so is stretched, and 1600x1200 gaming on my PC is stretched, which looks horrible. I have read that the PS3 is also affected by the 1080p issue.
     
    I tried going to the NZ technical support page but entering my customer code or order number do not return any results. I tried the order status page too, which also does not find me or my order. I am getting the numbers straight off my invoice.
     
    What steps will I now need to take to receive a replacement that will work fine with my PS3?
    Is there a reference number/engineering notice number or something like that for this issue to speed things up if Dell NZ are not aware of this problem?
     
    Thanks again,
     
    Grant
     
     
     


    Message Edited by Buckchoi on 03-07-2007 03:27 AM

    Message Edited by Buckchoi on 03-07-2007 03:29 AM
  • DELL-Chris M

    Community Manager

    •

    56891 Posts

    •

    232143 Points

    436

    0

    Posted March 7th, 2007 12:00

    All,

    There is not an actual "process". You just have to show the technicians that you have the issue and get an exchange. There is only one part number for the monitor. This means, when you initiate an exchange for a defective monitor, there is no way that we can know what revision you will receive. You might get an A04, or you might get an A03. There is no way for us to know until you open the box.


    DELL-Chris M (old account)

    #IWork4Dell

  • 241

    0

    Posted March 7th, 2007 20:00

    Okay, so I have not yet been able to reach the proper person by phone... The Technical Support hotlines, at least in Canada, don't deal with monitors or something, because I keep getting to the wrong people. I called Customer Care, and they sent me to Technical Support again, though they gave me a case number. Problem is, when I get to the Technical Support, it asks me to press 1, 2, 3, 4. None of which options come even close to mentioning displays. I've been on hold long enough that it's annoying, so I'm asking on here, if anyone knows the proper number to call in order to get tech support for this monitor.