
UNSOLVED
D
Daisyguarddog
8 Posts
0
70009
August 2nd, 2013 01:00
Ultrabook XPS13 L321X Hangs during sleep mode
Hi, I have had this ultrabook for 9 months and it works fine except when you put it to sleep.
Once asleep, the ultrabook behaves as it should for about 2 hours with the front white light glowing on and off and when you bring it out of sleep it operates fine.
After two hours or so, the white light comes on hard and the laptop cannot be woken up. I have to hold down the power button for 10 seconds and fully reboot the system.
If I leave the laptop asleep on battery power, then after about 6-8 hours, the batter is flat too.
This occurs whether the ultrabook is plugged in or on battery power. I am running Windows 7 Professional 64bit.
There may be something waking it up but I cant find out what it is.
Any help appreciated.
Responses (15)
Solutions (0)
Daisyguarddog
8 Posts
1781
0
Posted August 5th, 2013 18:00
Hi,
Thanks for the advice - I have followed all the steps with no success. Bios was already up to date as were most of the drivers.
System still does not wake up after more than 2 hours in sleep mode and I have to hold down the power button for 10 seconds then reboot.
The only step I haven't taken I to fully reload windows.
Any further suggestions? Is there a log I can generate to post here for review by you?
Regards
DELL-Babita S
4 Apprentice
•
1313 Posts
1781
0
Posted August 6th, 2013 07:00
Hi Daisyguarddog,
Alongwith the BIOS, did you also update the video driver? Were you able to try the Lockup Troubleshooting steps to resolve the issue?
Please click on the link below for FAQs on sleep and hibernation. This link may be helpful in understanding the issue with your computer and also troubleshoot the issue.
Let us know if further help is needed.
Thanks and regards,
Babita S
#iworkforDellFor easy access to drivers, manuals and product updates, please visit our Support Site .
DELL-Babita S
4 Apprentice
•
1313 Posts
1781
0
Posted August 8th, 2013 06:00
Hi Daisyguarddog,
Unfortunately we have not received feedback from you on this topic. If you need continued support, please respond to my post.
Thanks and regards,
Babita S
#iworkforDellFor easy access to drivers, manuals and product updates, please visit our Support Site .
Daisyguarddog
8 Posts
1781
0
Posted August 8th, 2013 16:00
Hi, Thanks for the advice. I have tried all the processes you suggested and loaded the drivers as suggested with no success. The system still does not wake from sleep after a few hours.DELL-Babita S
4 Apprentice
•
1313 Posts
1840
0
Posted August 10th, 2013 10:00
Hi Daisyguarddog,
We understand how frustrating it can be when an issue does not get resolved even after you have tried all troubleshooting steps possible.
Since you have already updated BIOS and video drivers, please try steps as mentioned below:
- As soon you see the Dell logo on your screen, tap to enter the system setup.
- Press F9 to Load Setup Defaults
- Press F10 to Save and Exit the BIOS screen.
Hopefully, loading the default BIOS settings should help resolve the issue. Please reply with results.
Thanks and regards,
Babita S
#iworkforDellFor easy access to drivers, manuals and product updates, please visit our Support Site .
Daisyguarddog
8 Posts
1840
0
Posted August 11th, 2013 16:00
HI, Thanks again - I did load default settings in the bios as suggested and no luck - system still does not wake from sleep.
No change in the behaviour of the system.
DELL-Babita S
4 Apprentice
•
1313 Posts
1840
0
Posted August 13th, 2013 09:00
Hi Daisyguarddog,
Thank you for your reply.
We are sorry to learn that the troubleshooting steps mentioned so far have not resolved the issue.
Follow steps below to change the power settings on your computer to "High Performance"
- 1.Open Power Options by clicking the Start button,clicking Control Panel, clicking System and Security, and then clicking Power Options.
- 2.Under the plan that you want to change, click Change plan settings.
- 3.On the Change settings for the plan page,choose the display and sleep settings that you want to use when your computer is running on battery (if applicable) and when it's plugged in.
Also, please check to make sure that mouse and keyboard settings are set to allow the device to wake the computer from sleep.
To allow a mouse to wake your computer:
- Open Device Manager by clicking the Start button, clicking Control Panel, clicking System and Security, and then, under System, click Device Manager. If you're prompted for an administrator password or confirmation, type the password or provide confirmation.
- In the list of device categories, double-click Mice and other pointing devices.
- Right-click the entry for the mouse, and then click Properties.
- On the Power Management tab, select and Check the Allow this device to wake the computer check box, and then click OK.
Please let us know if the steps mentioned above were helpful in resolving the issue you are facing with the laptop.
Thanks and regards,
Babita S
#iworkforDellFor easy access to drivers, manuals and product updates, please visit our Support Site .
Daisyguarddog
8 Posts
1840
0
Posted August 15th, 2013 20:00
Hi,
I selected a standard power setting - high Performance.
I checked to ensure the Allow device to wake the computer was checked - and it was. However when there is no mouse connected, there is no option.
Again, I put the lap top to sleep - unplugged form power and all other devices - no mouse connected either.
In the morning, the laptop was drained of all battery power and after plugging the power back in, booted from scratch again.
So, in effect - no change.
Is there any log or report I can generate and attach for you to review?
DELL-Babita S
4 Apprentice
•
1313 Posts
758
0
Posted August 20th, 2013 03:00
Hi Daisyguarddog,
Thank you for your reply. I apologise for the delay in replying to your post since I was looking for an appropriate resolution for this issue.
Please run the sfc /scannow command (System File Checker) which will scan the integrity of all protected Windows 7 system files and replace incorrect, corrupted, changed/modified, or damaged versions with the correct versions if possible.
If you have modified your system files as in theming explorer/system files, running sfc /scannow will revert the system files such as explorer.exe back to it's default state. Make the appropriate backups of your system files that you have modified for theming if you wish to save them before running sfc /scannow.
Steps for running sfc /scannow:-
- Open an "elevated command prompt" (right click -> Run as Administrator)
- In the elevated command prompt, type sfc /scannow and press Enter.
- When done, close the elevated command prompt.
Secondly, to stop hibernation, enter the Start menu and in Start Search, type cmd and press Ctrl + Shift + Enter to run Command Prompt as an Administrator
In the black box write " powercfg -h off " and press Enter. Wait 5-10 seconds and close the window.
Hibernate will now cease function as active and the large hiberfil.sys file will disappear . To activate it again, follow these steps, but type "powercfg -h on".OR
Open the Control Panel from the Start Menu
Open Power Options in the Control Panel
Select Change Plan settings next to the power plan in which you want to disable hybrid sleep
Select Change Advanced power settings.
Select Change settings that are currently unavailable in the Power Options window
Set Allow Hybrid Sleep under Sleep to Off and then click OK to save the changesYou may also find this Microsoft link helpful: http://dell.to/13BO8co
Also, please check if you have an always "On" Wireless router which may be keeping the computer awake.
Please keep us posted on the results.
Thanks and regards,
Babita S
#iworkforDellFor easy access to drivers, manuals and product updates, please visit our Support Site .
Dell Community Forum will be performing site maintenance between August 21st and August 23rd, 2013. You may also reach us on Facebook and Twitter for Support.

DELL-Babita S
4 Apprentice
•
1313 Posts
1781
0
Posted August 2nd, 2013 01:00
Hi Daisyguarddog,
Welcome to Dell Community Forum.
In some cases suspend/hibernate issues can be caused by incorrect or outdated BIOS settings or video drivers. Be sure to regularly update your drivers to take full advantage of your hardware and software.
Please click on the link below for Computer Does Not Wake Up or Resume from Suspend/Hibernate Mode
http://dell.to/12Lm1Dq
Plug your computer to a good, working UPS before you update the BIOS. If you experience a loss of AC power or a significant voltage sag/spike during the BIOS flash, you will either have to replace the BIOS chip or motherboard. Disconnect all external peripherals and ensure there is no cd/dvd in the optical drive prior to updating the BIOS on your computer.
Please reply if you have further queries.
Thanks and regards,
Babita S
#iworkforDell
For easy access to drivers, manuals and product updates, please visit our Support Site .