UNSOLVED

coglananth

updated

23 years ago

Closed

0

13367

April 11th, 2004 04:00

Is there an adaptor or converter to connect a parallel printer to a USB port?

My problem is I am trying to connect a Hewlett packard printer (Deskjet 670c) to an Inspiron 8600 notebook, The Deskjet printer has a Parallel connector on it (eg a DB25 male plug). My Inspiron all though it has a parallel port on the back of it, apparently it is not connected internally. so my question is can i plug this parallel plug (for printer) into a USB port via some sort of adaptor or converter?
  • Oditius

    2 Intern

    •

    808 Posts

    776

    0

    Posted April 11th, 2004 11:00

    I googled your question and came up with this:

     

    http://members.optushome.com.au/awni/Page101.htm

     

    Hope this helps.

  • RedsB3

    106 Posts

    776

    0

    Posted April 11th, 2004 15:00

    The port is part of the motherboard, so it is more likely you have different issue.  What happens if you connect the printer to the port and turn it on?  Have you tried adding it through Printers & Faxes in the control panel.  Support for this printer should be built into XP, the native driver should work.  Have you looked in device manager to see if it is recognized, or if your lpt port is recogniized?  If you tried to install the printer using the software that came with the printer, that could be your problem.  When the 670C was made, there was no xp, there is no support for it on the software.  The native drivers in xp will operate it just fine.  I had an old 610 connected to my notebook for quite a while, all I had to do was plug it in, connect the parallel cable and turn it on, xp detected it and installed the drivers automatically.
  • 776

    0

    Posted April 12th, 2004 01:00

    Cheers that helps as i have been to about 5 different computer shops and they dont think there is such a thing. I guess it pays to look in the right place.

    Thanks again.

  • 776

    0

    Posted April 12th, 2004 02:00

    When I connect printer to the parallel port and install printer through add printers & faxs the wizard does not detect the printer when i ask it to "find local printer automatically",  I then installed it manually, the printer icon appears in the printer & faxs menu and it set as default, so i think the software is installed properly, when i try to print a message appears on taskbar saying "this document failed to print"

    When i look in device manager and look at "Ports (COM & LPT) it shows  "Printer port(LPT3)" and it has a yellow exclimation mark next to it. I then look at the properties for "printer port (LPT3)" and it shows this message.                                                                                                                                                                                                               Windows cannot determine the settings for this device.  Consult the documentation that came with this device and use the Resource tab to set the configuration. (Code 34).

    I have looked at my reciept for when i purchased my computer and it says this "No Parallel Port, No Serial Port, No Infra Red Port and NO SPDIF Support" so i assume the parallel port is not connected internally. If this is the case then i can only see the option of an adaptor cable.

    Thanks for your response.

  • jk79

    412 Posts

    776

    0

    Posted April 12th, 2004 04:00

    Sounds like you may have gotten a transitional 8600.  They phased out the legacy ports on those systems, so the parallel port may indeed be non operational.  There is one thing you may want to try....  I believe that BIOS release A05 for these systems disabled the legacy ports on even the the older systems that were supposed to support them, much to the awe and disapointment of those who had the older systems; that BIOS release was quickly pulled.  You may want to try switching to a different BIOS revision if you are running A05.  I would suggest A04 as I have read of some users having problems with A06.

    JK

    If this does not work, try looking for a port replicator that will work with your system and has a parallel port.

    Message Edited by jk79 on 04-12-2004 01:35 AM

  • Oditius

    2 Intern

    •

    808 Posts

    776

    0

    Posted April 12th, 2004 11:00

    I understand the the i8600 I have, has a working parallel, serial and infrared port (I know they work because I didn't have a USB printer), but the i8600c did not. It doesn't make a whole lot of sence to phyically have the ports there, but not useable.

     

  • jk79

    412 Posts

    776

    0

    Posted April 12th, 2004 19:00

    I'm thinking that the system in question was ordered after the 8600C was introduced, but Dell still had some of the old hardware on hand.  Rather than make things confusing by offering both models concurrently, I imagine they disabled legacy ports in the BIOS and sold them at the same price point as the non legacy models.

    JK

  • shinecello

    42 Posts

    776

    0

    Posted April 14th, 2004 14:00

    Have these new 8600c chassis got a different motherboard?