
UNSOLVED
I put an SSD in an Inspiron 6400.
...and the results are, well, amazing to say the least. Even at SATA1 speeds to which the motherboard is locked to, it's definitely a vast improvement over my previous tired Hitachi 5400rpm HDD. Startup time is relatively fast too:
http://www.youtube.com/watch?v=xZBsRUqInus
Some might say it's not worthwhile to spend an embarassingly huge amount of money on an old system like the Inspiron 6400 (I paid ~USD 215 for my 80GB X25M), but if youre already planning to upgrade or replace your disk drive, seriously consider an SSD, especially when prices start to fall when they go mainstream. :emotion-2:
Responses (4)
Solutions (0)
Rather than trying to use some hack like Dataram, I would suggest reinstalling the 64bit version of Windows 7, which will natively be able to access the additional ram.
When you owen a copy of Windows 7, your license key is good for either the 32 or 64 bit version of the package level you own, provided its not the starter edition, which is 32 bit only.
I use a 96BG OCZ Vertex SSD on my laptop, and a 120GB OCZ Agility on my Desktop. The speeds and silence are more than worth the high cost and rather limited drive space, but because they are small, I have a linux server running with SAMBA in my closet, attached to a 7.25TB redundant array of drives to store my data.
I have never checked to see if my Windows 7 correctly identifies and enables Trim support, though I have been told Windows 7 automatically adjusts for SSD's on install to an SSD. If you image the partition to your new SSD, instead of doing a clean install, it may not have detected that you are now on an SSD, and thus may not be configured properly.
mikecrivellaro
4 Posts
3754
0
Posted October 25th, 2010 16:00
My intel controller in my Inspiron is 82801GBM (ICH7-M/U) LPC Interface Controller - 27B9
Intel 945 express chipset
So, the Intel Driver optional download needed for trim support, 9.6.0.1014, should work.
This should allow my Inspiron 6400 to support the trim function, correct?
I have seen people complaining about the A17 BIOS. Does the BIOS determine which mode it is in? RAID, IDE, or AHCI
Or Does the Microsoft System Management BIOS Driver determine the mode? How do I change it to AHCI, if that is the case.
Once I download the optional driver 9.6.0.1014 via F6 setup, I should be able to use the fsutil command to check my Trim status.
Is this correct, anyone?
I also have a Dell Inspiron 6400 and have not been having any luck installing WinXP or Ubuntu 11.04 on a new OCZ Vertex 2 Plus SSD 120GB drive. I've been able to format the drive with GParted from a live Ubuntu session running off of a thumb drive and can then see my partitions when installing from that thumb drive. The install seems to succeed and I'm asked me if I'd like to continue working or reboot. I say reboot and it tells me to remove my install media. I remove the USB stick, reboot and the install seems to work just fine. It boots back up into Ubuntu but then when I shutdown again, the shutdown hangs at the screen that just says "Ubuntu" with the 5 cycling progress dots. These dots just continue cycling forever so its not truly hung, but it wont shut down. Like its waiting on something. Eventually (half hour) I kill power manually and it comes back up and I get a Grub error. I've now installed half a dozen different times trying Ext2/3/4 and trying my Ubuntu partition at the beginning and middle of the drive. I've previously had Ubuntu installed on an older 5400RPM IDE drive. I don't think the disk is dead because the install works smoothly. Any other thoughts on what to try? I've also dropped to another temrinal (CTRL+ALT+F1/2/3/4/5/6) to see what was running but this is hung and I can't type anything.
And I'm having similar screwy install issues trying to install WinXP. Its detects my NTFS partitions formatted from GParted (and I've also tried creating those partitions from the WinXP install). It goes through the initial WinXP blue text only install screens. Then gets to the "X minutes remaining". This screens displays momentarily and then the screen goes blank and nothing further happens.
I'm not sure if these issues are related, but I've had WinXP and Ubuntu dual booting nicely for quite some time on my old 5400RPM IDE drive. I've read that the Dell BIOS does not support AHCI. Could this have anything to do with my problems? Did you have to do anything to get your install to work?
Thanks!

mikecrivellaro
4 Posts
3754
0
Posted October 25th, 2010 11:00
Are you using Windows 7? I have upgraded my Inspiron 6400 to Windows 7 32-bit, 4GB of memory, and added a OCZ Vertex 2 120GB SSD for speed. However, I could not get the Windows 7 Trim Support to verify that it was working using the "fsutil" program. How about you?
Also, I am thinking about using RamDisk by Dataram to access the extra memory not seen by the 32-bit system. I could have the temporary internet files, temp files, and page files sent to the RamDisk partition to preserve the SSD.
Or, I was thinking of an Expresscard 34 SSD to do the above function.
Any thoughts on the "fsutil" problem with my setup? Mike