UNSOLVED

aln688

updated

19 years ago

A

aln688

70 Posts

0

24270

May 5th, 2008 17:00

XPS 420 eSATA port

Hello,

 

I have an XPS 420 with BIOS A03 and am running Windows Vista. I'm currently using two internal SATA hard drives and one internal SATA DVD writer, all three work fine.

 

The problem I have is I bought a Seagate FreeAgent Pro drive and an eSATA cable and have plugged the drive into the back of the computer into the eSATA port, but Vista nor the BIOS seems to recognize it's even there.

 

For the BIOS options I have enabled the External SATA port setting to "On" and the RAID settings are set to "Raid On", not because I'm running RAID but mainly because I want AHCI functionality.

 

Any ideas? I'm unsure what else there is I have to set/modify to get this external HDD working.

 

Thanks,

Adrian.

  • aln688

    70 Posts

    350

    0

    Posted May 5th, 2008 18:00

    I already followed those instructions and no luck, thanks though.

     

    Sadly, I was "chatting" online with Dell technical support and he told me that because Vista and eSATA are new technologies that there will be issues getting Vista to recognize my external drive.

  • xfaega

    1 Rookie

    •

    191 Posts

    350

    0

    Posted May 5th, 2008 18:00

    Did your Seagate come with any cds?  If so us it to format your HDD.  The system won't see the drive until it has been assigned or you have run the cd for the Seagate.  The Seagate cd will see your drive and format it or assign the HDD a Letter like F:.  Try this.
  • aln688

    70 Posts

    350

    0

    Posted May 5th, 2008 19:00

    It didn't come with any CDs, just the drive, a USB & Firewire cable, a Firewire module to attach to the drive and power cable, that's it.

     

    I've been looking on this forum and it seems Dell was plagued with this eSATA port not working issue, although I'm at a loss to determine what the exact cause is. I see "solutions" like hacking part of the connector off on the external HDD, a potential or called for BIOS update and installing drivers in a certain order.

     

    I'm waiting on Dell technical support calling me back.

     

    Thanks.

  • aln688

    70 Posts

    350

    0

    Posted May 5th, 2008 19:00

    packerFan07,

     

    You got an enclosed CD with your FreeAgent drive? What did it have on it? Either way, I don't know what a CD would contain, other than backup software, drivers aren't usually required for a plug'n' play drive.

     

    So your SATA works on your XPS 420?! Interesting. When you say AHCI drivers loaded on both controllers, which controllers are you talking about? I thought there is only one controller, the one inside the ICH9R chipset that enables six SATA ports? My "iaStor" driver "Startup" value is set to 0, so it's loading.

     

    I'll look at your link. Thanks again.

  • packerFan07

    705 Posts

    350

    0

    Posted May 5th, 2008 19:00

    I have the 1 TB FreeagentPro external SATA on my 420 working - so yours shouldl work. Are the AHCI drivers loaded to both controllers? I did use an enclosed CD as well...

     

    These were the instructions I followed to enable the eSATA port (not the same link as listed above)...

    Message Edited by packerFan07 on 05-05-2008 03:08 PM
  • packerFan07

    705 Posts

    350

    0

    Posted May 5th, 2008 20:00

    ... 
    -Double Click IDE ATA/ATAPI controllers
    -Right Click Intel(R) ICH9 2 port Serial ATA Storage Controller 2
    ...
    - Click Close and follow the same steps to update the driver for the Intel(R) ICH9 4 port Serial ATA Storage Controller 1
    ...
    there are 2 controllers - I believe one is for all the internal drives and one for the external drives.
  • aln688

    70 Posts

    350

    0

    Posted May 5th, 2008 20:00

    I don't have those listed under DEVMGMT.MSC. All I have are:

     

    * Intel ICH8R/ICH9R SATA RAID Controller

    * Microsoft iSCSI Initiator

     

    Maybe if I had my BIOS setting set to Raid Autodetect / ATA I would see them, but right now I suspect if I changed it Vista would crash upon boot.

     

     

  • xfaega

    1 Rookie

    •

    191 Posts

    350

    0

    Posted May 6th, 2008 00:00

    It has something to the cd that should have come with your Seagate.  Go to seagate website and see if there is a download for it.  The reason I say this is because my seagate is the only ext. HDD that works with the eSATA.  I have 4 WD ext. HDD in the same case and none will work on the eSATA. 
  • aln688

    70 Posts

    154

    0

    Posted May 6th, 2008 01:00

    Hmm, maybe it's the Seatools software on that CD? The diagnostic software. I thought that was pre-loaded on the actual drive, mine was. I have the 500GB external FreeAgent Pro.

     

    So your external WD drives don't work on that port, but the Seagate does? Unbelievable, I don't stand much chance then. I suppose it was too much to ask that it just "works" when I plugged it in.

     

    I'm using a brand-new Vista Ultimate installation, with Intel Matrix Storage driver and the Raid On setting used in the BIOS. Obviously the External Sata port is set to "On" as well, it's baffling. I just don't know what else would stop it working.

     

    Thanks, glad to hear your system is fine.