UNSOLVED

rallen1022

updated

13 years ago

R

rallen1022

1 Rookie

•

7 Posts

0

126599

March 21st, 2013 13:00

Optiplex GX620 Will not start, no lights; amber light only on MB

I have several GX620's I am rehabbing and none will turn on; I see an amber light on the motherboard, but cannot tell if this is a PS issue or a MB issue?

Any suggestions?

Thanks

  • DELL-Nikhil D1

    6 Operator

    •

    2580 Posts

    2995

    0

    Posted March 21st, 2013 13:00

    Hi rallen1022,

    To isolate the issue, I would like you to remove all the external peripherals connected to the system tower, remove the power cable, press and hold the power button for 20 seconds. This process will drain all the static energy from the computer.

    Now connect only the power cable, display cable to the monitor and restart the system.

    If the system is beeping please listen to the beep sounds carefully and count the number of beeps and the order in which the system beeps. And also check the status of the 4 LED lights on the front of the system tower (1,2,3,4) and reply with the LEDs lights status and beeps sounds if any. Also include the status of power button LED light.

    I would check the problem depending on the status of LED lights and help you further.

    Please reply for further help.

  • rallen1022

    1 Rookie

    •

    7 Posts

    3003

    0

    Posted March 22nd, 2013 07:00

    Thank you NIkhil,

    Nothing is plugges into the box; I have repeatedly removed the power cord and pushed the power button to clear the box. I have no back lights at all, no beeps, nothing once I reconnect the power cord and press the button. I do have a light on the MB though, so I am getting juice that far.

  • speedstep

    11 Legend

    •

    46969 Posts

    3003

    0

    Posted March 22nd, 2013 11:00

    If you have several you should be able to tell by using a good one to test the power supplies one at a time. Amber light on the motheboard only indicates that 5v standby is on. IT ABSOLUTELY IN NO WAY INDICATES Good Hardware. Thats what the 4 diagnostic lights and the power button light are for.

  • rallen1022

    1 Rookie

    •

    7 Posts

    3003

    0

    Posted March 26th, 2013 12:00

    Issue solved. I replaced the PS and I am running like a fiend now. Thank you Nikhil and Speedstep for your good help.

    Ron

  • davsr66

    4 Posts

    3003

    0

    Posted December 4th, 2013 10:00

    Hi,

    I have the same issue, the pc is a gx 620 optiplex, when i hit the power button it lights up then shuts down, the 4 # lights blink on then 1 and 2 go off and show only 3 and 4 before it shuts down. Luckly i have a spare and i am going to use the PS and swap them out to see if (like Ron) this fixes the issue. Any other input will be helpful.

    P.S. I swapped the PS and got the same result, so i then swapped the hard drive from the current to the spare and got it up and running, I am assuming this is a motherboard issue, since i do not have the time to completely troubleshot this issue as this is a production pc i will leave that for later.

     

    Thank you,

     

    Dave

  • davsr66

    4 Posts

    3003

    0

    Posted December 4th, 2013 10:00

    Maureen,

    The issue just started, I did a PM on this pc last month and was told when i came in that it would not start up, I looked it over for loose cords, made sure it was plugged in lol (not kidding) and started to troubleshoot the pc, once i covered the basics i googled the model and came here.

    Thank you, i will look into the memory next, It would not stay on but 3 to 4 sec and would not display any output before shutting down, no beeps either. I did take the spare and swap the good hard drive to it and fired it right up. Since i do have 2 other retired pcs either 620's or 745 i will continue to test the unit as time permits.

     

    Thanks for the AWESOME speedy respounce.

    Dave

  • 3003

    0

    Posted December 4th, 2013 10:00

    Hello Dave,

    The 3 and 4 diagnostic lights indicate a memory configuration issue or failure.  Do you happen to have known good memory to swap in?   If you do not have known good memory, you can perform the memory dance, testing one stick at time in the primary slot, to see if one stick has failed.   Should you need it, here is a YouTube video on installing memory on the Optiplex 620:  http://www.youtube.com/watch?v=h3jR2-CHEno  If you have another system  in which you can test the memory from this system, even better.   The memory may have worked itself loose and reseating the memory may resolve the issue.  If the memory is fine, there may be an issue with the memory slots on the motherboard.

    Is the system providing any other diagnostic assistance?  Is it on long enough to run diags?  How about beep codes?  Anything that would help isolate the cause and confirm what the diagnostic indicators are showing?

    When did  the problem start?  Was any new hardware or software introduced on the system before the failure?  Are you seeing any other symptoms?

    Please let us know what you discover and if you are able to isolate the cause.

    ~Maureen

    #iwork4dell

  • davsr66

    4 Posts

    3003

    0

    Posted December 4th, 2013 11:00

    Well, back to the drawing board, the spare pc runs as long as nothing is connected, (cd rom, video card, etc) once i put it all back together it would simply reboot every two mins. So i took the first pc and reset the memory, didn' work, put the memory from the spare in the pc, still same thing, power button lights for a sec or two then goes out. see,s like i have two different issue with both pc's. Going to pull out all the old retired pc's to see if i can get one that will work.

     

    Thanks again,

     

    Dave

  • 3003

    0

    Posted December 4th, 2013 13:00

    Hello Dave,

    When you bring it down to the bare bones and it works fine, what all is connected?  The original hard drive, keyboard, monitor, and memory?  What happened when you tested each one of the peripherals by itself?  One of those peripherals may be causing a short.

    Let us know what you discover when you are able to test with the retired pc's.

    Waiting to hear from you,
    ~Maureen
    #iwork4dell

  • davsr66

    4 Posts

    426

    0

    Posted December 5th, 2013 11:00

    Maureen,

    I took all the peripherals off the retired pc optiplex 745 (video card, cd/dvd rom, keyborad and mouse), put the hard drive in from the production unit, and had to find an older keyboard and mouse that would work with the system.

    Fired it up and it paused and stated, it did not find a drive on sata 0, so i swapped the cable from sata 1 (where the original HD was) to 0, received the same message, however I hit F1 and it booted right up. And it currently running as I type. I, as you suggested, will next start adding peripherals back on one at a time to see what is making it reboot. As i get more info I will add it here.

    The production unit will not start, even stripped down to nothing. I am thinking MB. Too old to be worth replacing.

    Thank you,

    Dave