UNSOLVED

GlitchBob

updated

18 years ago

G

GlitchBob

22 Posts

0

19551

June 30th, 2008 18:00

How would I go about installing an older HDD in a XPS 630?

So my old primary drive from my Dell 8200 has a lot of files on it, that I'd like to transfer over (or just move them over to my primary XPS 630 drive, then reformat the old drive, and place them  back on there) to my new XPS 630's drive.

 

However I've noticed one tiny problem... since it's older, it can't connect to the newer cables. Are there some sort of adapaters or something I could use? Or maybe since I have leftover IDE cables, is there a place I can plug them into (although that would still leave the issue of power).

 

For refernce the old drive is a Seagate Barracuda ATA, model ST380021A, 80GB.

  • PETER345

    1 Rookie

    •

    5796 Posts

    483

    0

    Posted June 30th, 2008 19:00

    The simplest way to connect an IDE drive to an all SATA system is to use an USB adapter for IDE or an external enclosure for the IDE drive (same thing, but with a case around the drive).  You can get them for under $20 and are very convenient for accessing drives in another system.  I have one that connects IDE, laptop IDE or SATA drives to USB.

     

    Peter

  • Merlin_AZ

    42 Posts

    483

    0

    Posted June 30th, 2008 19:00

    Or, just plug the drive into an IDE ribbon, plug the ribbon into the IDE controller of the motherboard, plug a molex power connector to the drive, make sure the jumper is set to master, and boot up.

    If it's not recognized, you may need to turn on the IDE controller in the BIOS.

    If you want, you could screw the drive inside the HDD cage, or shut down and remove it.

    Message Edited by Merlin_AZ on 06-30-2008 03:51 PM
  • PETER345

    1 Rookie

    •

    5796 Posts

    483

    0

    Posted June 30th, 2008 20:00

    That's too easy!  :smileywink:

     

    I thought that machine was SATA only.

     

    Peter

  • PETER345

    1 Rookie

    •

    5796 Posts

    483

    0

    Posted June 30th, 2008 21:00

    Not the D9200/X410.  They have no PS/2, no printer, no serial and no IDE.  I think Intel was trying to force the death of these legacy ports.  Ah that's it ...  this is not a Intel chipset machine.

     

    Peter

  • Drange

    155 Posts

    483

    0

    Posted June 30th, 2008 21:00

    The XPS 630 has an IDE port.  Just plug in your "old" hard drive using the IDE cable it's on in your old computer and it will auto recognize.  You should be able to access it when windows boots up.
  • Merlin_AZ

    42 Posts

    483

    0

    Posted June 30th, 2008 21:00

    Most newer boards still carry 1 IDE controller.
  • GlitchBob

    22 Posts

    483

    0

    Posted July 1st, 2008 01:00

    Ok, so the IDE part is easily taken care of, but what about that molex power connector... so far I don't see any that would be correct for this drive (though I'll take another look).
  • Drange

    155 Posts

    483

    0

    Posted July 1st, 2008 02:00

    There should be a connector in there that will work, if not you can buy one for a couple of bucks at a Best Buy type place.
  • GlitchBob

    22 Posts

    483

    0

    Posted July 4th, 2008 20:00

    I managed to plug in the other HDD (which was lots of fun, I had to nearly remove the huge nVidia card to gain access to the larger IDE port)....but when I startup it says no boot device found... It's set to slave, so I'm not sure what's going on....?
  • Drange

    155 Posts

    163

    0

    Posted July 4th, 2008 20:00

    You have to go into the bios and set the HDD priority for your main HDD.