Inspiron 5675, NVMe SSD not detected sometimes in BIOS
I have a Dell Inspiron 5675 desktop with Ryzen 5 1400, MSI Radeon RX580 OC, 16 GB of RAM, and the Toshiba DT01ACA100. I just installed an ADATA XPG SX6000 Lite NVMe SSD into my computer, I found that it sometimes isn't detected in the BIOS but I can still boot to it if I manually select it in the boot menu. When I clear the CMOS, the drive will show up again but then disappear if I put the computer to sleep or reboot. I can still boot to the SSD even though it isn't showing up in the BIOS. Is it the SSD or the computer acting weird? I'm not really sure what to make of this. Could it be a bug in the BIOS?
The drive wasn't written to death. It was a brand new drive, never been formatted. I have returned the drive and got a different one from a different brand. No problems at all.
I did check my BIOS and it is v1.3.7. I did re-flash it just to make sure it wasn't corrupt or anything and that made the SSD show up temporarily. Putting the computer to sleep and then waking it up makes the machine reboot and the SSD is no longer recognized in the BIOS but is still bootable from the F12 menu, sometimes. Clearing the CMOS using the mobo jumper makes it come back until the machine is powered off.
@AvidSurvivalist wrote: the SSD show up temporarily. Putting the computer to sleep and then waking it up makes the machine reboot and the SSD is no longer recognized in the BIOS but is still bootable from the F12 menu, sometimes.
Sounds like a hardware problem.
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired) - Like many of you, I can appreciate a good game-engine. - I answer questions here, but I'm not a Dell employee. - Consider giving posts you like a "thumbs-up" - Posting models-numbers and software versions speeds trouble-shooting. - Click "Mark as Accepted Answer" on any post that answers your question best.
A weak/dying motherboard battery? It's a CR2032 3-volt coin cell, ~$2.
You might want to replace the battery first since it only costs a couple of bucks, even if that only rules the battery out, before worrying about failed SSDs, etc.
Open BIOS setup and copy down all current settings before you remove the old battery. Then power off, unplug and press/hold power button for ~15 sec before opening the case. Press/hold power button for ~30 sec after removing the old battery and then install a fresh one.
Go with a name brand battery, not some El-Cheapo brand that will die next week. :Wink:
Would the CMOS battery really die within a year? I'll try that, I think I have some spare Energizer CR2032s somewhere. I have contacted ADATA, the makers of XPG and am waiting for them to get back to me.
It doesn't show up in the BIOS but I can still boot from it. But then it sometimes does show up in the BIOS. I'm not sure if it's the drive or not as I don't have another NVMe drive.
Well, we don't know how long that battery sat around, installed in that motherboard -or not- before you bought this PC.
And the PC was likely unplugged while you were installing the SSD, so the battery was the only source of power to hold BIOS settings during that time, which could have drained it.
Besides, a battery is a cheap fix, assuming it solves the problem...
I replaced the battery. It still acts wonky though. I can't directly boot from a shutdown nor can I wake from sleep. I get that screen on the left. When I start up from a shutdown, it gives the screen on the left. I ctrl-alt-del and then it starts up.
Restarting is fine. When it does start, everything is fine, it starts in less then 5 seconds.
When the computer is in sleep and I wake it, turns on and then reboots to the same screen on the left. I'll do the same steps as above and it will go right into the OS. Everything is still open and in the same state was when I put it in sleep. I can't find anything in event viewer about what happened, nothing critical. I'm not really sure what to look for. I'll check for memory dumps but I have no idea how to read them nor would I understand it fully since I'm not a programmer, I'm just a Cybersecurity: Network Admin student.
I have run DISM image health check, chkdsk, and system file checker and those all reported no errors or corruption. I don't know if I mentioned this before but it is a new NVMe SSD, fresh Windows 10 install. Speedfan and msinfo32 shows the drive as a SCSi drive, not sure if that is supposed to be like that.
You're getting a Windows error, not a hardware error.
Read: Error code: 0xc000000e in Windows 10 for potential ways to fix this error, without doing a clean reinstall. You're going to need a bootable USB stick with the latest Win 10 ISO. You can download the Win 10 ISO file and instructions to prepare the bootable USB for free from Microsoft.
NOTE: That MS page says to use an 8-GB USB stick, but that's wrong. You need at least a 32-GB USB stick. Otherwise creation of the USB will fail. Sure wish MS would update their website! :Angry:
AvidSurvivalist
1 Rookie
•
18 Posts
10289
0
Posted July 28th, 2019 07:00