G5 Gaming Desktop - Flashing orange light on startup
Hello, I have an issue regarding my Dell G5 gaming desktop when I turn it on. Sometimes when I turn my computer on, it does not boot into Windows. instead, on the power button a flashing orange light appears. Normally the light on the power button is white.
Usually I would just turn my system on and turn it back on until it boots into Windows, however this is only a temporarily solution.
As others have described, it's most likely the PC booting and detecting no monitor.
I get the same issue with my Samsung Curved 27 CRG50 monitor, if I turn the screen on a moment later than the PC. Switch screen on and ready, before turning the PC on... no issues. Hope that helps.
Your switch sure sounds like it's contributing to the HDMI problem. Sometimes -for whatever reason- the PC doesn't see the monitor, possibly the order in which you're powering things on.
Since you have the GTX 1660 video card, it looks like you need this vBIOS update. Follow the instructions on that page carefull. BUT...if this were my system, I'd connect the monitor's HDMI cord directly to the PC without the HDMI switch and all those extra cables, before running that vBIOS update. Why take risks...?
Did you count the amber power button blink code? Blinks should appear in groups, 1 or 2 or 3 or 4 blinks, a pause, and then up to 7 blinks (how many in second group depends on number of blinks in first group).
If you get a 3 blink, pause, 1 blink error code (3-1), the issue may happen under two scenarios, with different causes, but with same symptoms:
Scenario 1 - Monitor being powered on 10 seconds after system has been powered on. Note: This only happens for certain monitor models (including but not limited to E2016H) due to the Hot Plug signal issue.
Scenario 2 - Connecting older monitors (including but not limited to E2016H, E2216H, P2217H, P2317H) with newer video cards (GTX 1660, GTX 1660 TI, GTX 1650, RTX 2060, RTX 2070, RTX 2060 Super, RTX 2070 Super), which is caused by a vBIOS incompatibility
Try below methods until the monitor displays successfully: * Power off both system and monitor. Power on monitor first, then power on the system * If first step does not work. Change the DP cable to HDMI/VGA cable, then retry first step * If issue persists, power off both system and monitor. Power on system, then power on monitor within 2 seconds. This method will only be applicable to certain monitors * Once the monitor is back on, update the video card vBIOS from Inspiron G5-5090 site to resolve the issue,
If you need to update the vBIOS, read an follow instructions carefully at that link.
I am unsure about the blinking pattern. This error occurs from time to time, it's not consistent but I will follow your advice by powering down everything, unplugging everything and hope that fixes the issue.
I should also note that I am using a Samsung 27" CR500 Curved Gaming Monitor (LC27R500FHNXZA). I am also using an HDMI switch (Rocketfish 4-Port HDMI Switch Box - RF-G1185-C), with the PC connected to the switch, then connected to my monitor. I am also using HDMI for all my video connections.
My graphics card is a NVIDIA GeForce GTX 1660 6GB GDDR5, so which BIOS update should I choose? There are many drivers available.
You want the monitor on and ready before you power the PC on. If that means powering the HDMI switch on first and giving the monitor a few secs to "get ready", that's probably what you have to do.
And run the vBIOS update for your card. Close all open apps and windows, in addition to connecting the monitor directly to the PC before running the update...
So the rule of thumb would be to turn my monitor on first, then my pc? However for my current setup my pc and monitor are connected to a HDMI switch.
Normally once I turn my HDMI switch on, the monitor would automatically turn on. And if there is no input to the monitor then the monitor would turn off autmatically (A flashing blue light appears on my monitor, indicating it's off)
So for my case I would turn the hdmi switch on first, then turn my computer on?
So it's the order on how things are turned on. Another user on this trend told me that I should turn my monitor on first, then turn my computer on, but for my case everything is connected to an HDMI switch.
When I turn my HDMI switch on, the monitor automatically turns on. So for my case would I turn the switch on first, then turn the pc on?
CocoPopsUK
31 Posts
11857
1
Posted June 12th, 2020 01:00
As others have described, it's most likely the PC booting and detecting no monitor.
I get the same issue with my Samsung Curved 27 CRG50 monitor, if I turn the screen on a moment later than the PC. Switch screen on and ready, before turning the PC on... no issues. Hope that helps.