UNSOLVED

ramu321

updated

14 years ago

R

ramu321

5 Posts

0

1762

July 14th, 2012 14:00

Vnx 7500 - SAS I/O and Bus connections

i read multiple hardware docs but still didn't get a clear picture of few things.

SAS i/o ( Assume we have 1 DPE and 1 DAE ):

one SAS I/O module in slot 0 of each SP ( A second SAS I/O module in slot 1 is optional )  Each I/O module has 4 ports.

SAS I/O modules ports  are connected from SPS --> DPE0 / DAE0 ....  ( SP A0 port 0 -->  DPE0 & SP B0 port 0 --> DPE0 ..etc. Basically 2 connections from SPS to each DPE/DAEs)

bus connections of DAE0 stmt is interchangable of  SAS connections of DAE0 ?

so it has 2 SAS connectons so can i read the above stmt as DAE0 has 2 bus connections  bus 0  and bus 1 ( bus 0 Enclosure 0 & bus 1 enclosure 0 )

  • Rainer_EMC

    6 Operator

    •

    8645 Posts

    462

    0

    Posted July 15th, 2012 07:00

    One connection from each SP to the DAE - so two in total

    Plus two daisy chain connections to further DAEs in case you have more DAEs than buses

  • ramu321

    5 Posts

    462

    0

    Posted July 15th, 2012 09:00

    hi Rainer,

    so question is  can i call this SAS connections as bus connection right .bec i confused with BUS term and purpose.here in this below picture Bus0 enclosure 0 and BUS1 enclousre 0 are SAS connections from SP A & SPB  and both consists of same disks ( enclosure ) b? pls correct me i am wrong.  thank you.

  • Vipin VK

    2 Intern

    •

    812 Posts

    462

    0

    Posted July 15th, 2012 10:00

    SAS connection, is the backend bus.

    There is no screenshot available here in your post. That may be why, your question is not clear..

  • Vipin VK

    2 Intern

    •

    812 Posts

    462

    0

    Posted July 15th, 2012 11:00

    I am still not clear with your doubt,.

    If it is about the drives : In VNX the drives are being identified by the Bus-id_Enclosure-id_slot. For example, The drive in the 5th(counting starts from 0) slot of the direct connected enclosure from backend port BE0 will have an address 0_0_5 (bus= 0, encl=0, slot=5 ) and the on the expanded (daisy chained) enclosure the addresses will be in the form 0_1_x .

    As you pointed in the snap, if you expand the BUS 0 ENCLOSURE 0 or 1 ( by clicking the + button to the left) you will see the drives in those enclosures, and those are addressed as I mentioned above. I hope this clarifies something for you.

  • ramu321

    5 Posts

    462

    0

    Posted July 15th, 2012 11:00

    sorry..here i attach the image

    Enclosure.png

  • ramu321

    5 Posts

    462

    0

    Posted July 15th, 2012 12:00

    i know...its kind of begineer to this emc hardware ,  i understand couple of thing here from ur input. can we tell how many DAEs this system has from this below image ..thank you so much for ur valualble answers & timeDAE.png.

  • Vipin VK

    2 Intern

    •

    812 Posts

    462

    0

    Posted July 15th, 2012 12:00

    It seems you have populated all the Bus with 2 DAEs, ie 16 numbers in total.. DAEs (Disk Array Enclosures) are the drive enclosures which are listed as Bus X Enclosure X in your snap.