Hi I'm trying to install a SSD for my XPS 435MT PC. Samsung 830 series. I need to but the PC in AHCI mode. My bios only has SATA or Raid. Dell tech support says to select SATA. I select SATA in the bios disconnected all other HD and connect the SSD. Did a clean install of windows 7. I saw no improvement in my system. Ran window bench mark and should the same results as my hard drive. Ran Samsung Magician Software to optimize the drive and OS. It keep reporting that PC was not in AHCI mode. Is there another setting in the BIOS I missed. Do I have to do a manual tweak to Windows 7.
I just got a Samsung 850 Evo 120 GB SSD installed today on my Dell XPS 435MT. My configuration was a single 500GB HDD with around 100 MB of partition for windows C:, a recovery partition E: and a large data partition D:
Basic process I followed was
Install the two softwares provided by Samsung
Shutdown the system.
Disconnect the DVD drive and instead plug in the SSD. I did this mainly because I did not have a spare SATA cable. I will have to buy one soon. For now, I used the one for my DVD/ BD drive since I almost never use the drive.
In the BIOS I changed from IDE to RAID but that caused some reboot so I changed it back to the way it was.
Booted into Windows as normal and did the cloning using the Migrate software I installed in step 1.
Cloning got over in 11 minutes for data around 40 GB of C: drive
After cloning I was prompted to reboot
In BIOS I set booting from SSD - basically changed the boot sequence
Rebooted
Windows from my SSD was up and running. My older Windows partition was changed from C: to F:. The new Windows from my SSD got drive letter C:
Did a check on the performance
I got a figure around 180 MB/s and around 250 MB/s for reads and writes respectively
Did performance tuning and OS optimization
Now the read and writes are well beyond the actual specs. I get 2500 and 2100 respectively.I still see Magician telling me that I should be in AHCI mode. I am not sure what would happen if I try to put into RAID. In step 4 I tried that but Windows would not boot. System would reboot every time.
I am happy with the initial performance improvement that I see.
If RAID isn't enabled you won't have AHCI - which means you don't have trim. So you have to find a way to get RAID enabled. The Fix at the above link should allow you to enable RAID and then boot into windows 7.
The XPS 435 MT is not designed to work with the Intel Responsiveness Technologies that make the system faster. This technology needs an mSATA module apart from the SSD and the SSD would only act as a caching drive.
For more information on Intel Responsiveness Technologies, please visit the link below:
When used on your system, the SSD would act just as an ordinary hard drive. The only benefit would be the longevity of the SSD over conventional hard drives. The difference in speed in this case would hardly be noticeable.
Let me know if you need further information or assistance.
Thanks for the reply, but is does not make sense the link you supplied says I need an intel 7 chip set which started shipping in august. So no PC manufactured prior to august can use a SSD for speed gain. mSATA refers to lap top SATA. I really need to get AHCI enabled. Dell tech support said I only need to select ATA in my bios, but that did not work. I know of people who have older PC that got AHCI enabled and get 20 second boot time. That is all I'm looking for.
The BIOS on the Studio XPS 435MT does not have the option for AHCI mode. It only supports SATA and RAID modes. On your system, the SSD would only work as a regular hard drive.
Let me know if you need further information or assistance. I will be glad to help.
This is what I learned this weekend talked to Samsung and searched the WEB it appears that as GauravS said is correct the XPS 435MT does not support AHCI, Dell support said it did. The XPS 435MT supports SATA revision 1.0 transfer rate is 1.5 Gbit/s. I bought a Vantec PCI host Card ($23.00) that supports SATA revision 2.0 3 Gbit/s transfer rate. The directions were vague and installation was not a smooth as I had hope. Will keep you posted on how it works out.
I bought my Studio XPS 435MT in April of 2009. The specs on my invoice state SATA 2.0 with a 3Gbit/s transfer rate.
Installing a SSD in the 435MT is not straightforward. There are a few "Catch 22" issues in that regard. TRIM support is absolutely vital with a SSD. Without it the SSD will eventually become as slow or slower than a regular HDD. In order for TRIM to function, the SSD must use an AHCI driver. It also will enable NCQ, giving you all the speed your SSD is capable of over SATA 2.0, which is a max of 3 Gbits/second. A side benefit is that it makes your SATA and eSATA ports hot-plug capable, though not necessarily hot-swap capable. (The difference is hot-plug means you can add a drive but not remove it, while hot-swap means you can add or remove a drive with the system running.)
Unfortunately, the Intel X58 + ICH10 chipset on the XPS 435MT's mobo is not full featured. Dell limits the chipset's capabilities. While the onboard Intel SATA controllers can support AHCI, they run in IDE mode by default. The BIOS is also limited to say the least, more like crippled actually. In the BIOS, under Advanced Chipset Features > SATA Mode, there is only a choice between IDE or RAID with IDE being the default. However, by selecting RAID for the SATA Mode, AHCI is enabled on all four SATA ports as well as eSATA. Of course, if you enable RAID after your OS is installed, everything on your SSD or HDD will be lost and you will have to reinstall the OS again. So, enable RAID in the 435MT's BIOS before installing the OS on your new SSD.
The next problem you will likely encounter is a failed install of your OS. This is described in the MS Knowledge Base Article 2466753 available here:
This is a known issue with both Windows 7 and Windows 8. Don't know about Vista though. There are workarounds involving editing the system registry by creating keys, subkeys, and values, as well as workarounds to the workarounds depending on what controller your SSD uses. Assuming at some point you get your system up and running from your SSD, there is one other problem that crops up when you insert a blank optical disk into your burner. Your system will likely either freeze or crash entirely. This is due to your optical drive(s) also running AHCI drivers when they should be using IDE/UDMA. When you select the RAID option for the SATA Mode in the BIOS, all the SATA ports switch over to AHCI. So, before you use your optical drive(s), check in Device Manager to see if you can change the driver for the optical drive's SATA controller in the OS to IDE/UDMA.
BTW, it's called "Intel® Rapid Storage Technology (Intel® RST)", not "Intel Responsiveness Technologies"
CPU-Z report for Dell Studio XPS 435MT:
Chipset & Memory:
Northbridge Intel X58 rev. 12
Southbridge Intel 82801JR (ICH10R) rev. 00
Intel Rapid Storage Technology Specifications for ICH10R Controller Hub list "TRIM support in Windows 7* (in AHCI and RAID mode for drives not part of a RAID volume)"
I didn't quite follow you at the end - were you saying that it is possible to switch the optical drive back to IDE using Device manager - or were you leaving that as an open question? I am (was) interested in installing an SSD - but your comments about "workarounds to the workarounds" scared me a bit. Were you successful?
argvargc
67 Posts
6106
0
Posted March 13th, 2015 11:00
I am happy with the initial performance improvement that I see.
It took me just 1 hour to do all of the above.