UNSOLVED

Coleco

updated

21 years ago

C

Coleco

53 Posts

0

4225

August 24th, 2005 18:00

New hard drive start up problems.

Hey all,
I apologize because I know this has been asked and answered before, but using everyones posts and recommendations I am still at a loss.
I pulled my old 8200 out of closet. Wife needs a computer for stuff and kids would like to play some games on it. I put in a new WD 120 GB hard drive. I have done things like this before in past so have some familiarity. I expected it to boot up to OS not found, or with windows xp in the drive it would start the installation. However, it gives me an error and asks to go to F2. I have done this like 50 times now. NO matter what jumper orientation I select (I know it is supposed to be cable select or the 2 space) it reads the hd as secondary drive 0. Now I have tried multiple different EDE cables and multiple different jumper positions but it always ends into F2 without advancement. In the BIOS it does say the hd is secondary 0 and does read it as having 120 GB . So my question is can anyone tell me the definite jumper position. Is it cable select (single jumper at position 2) or no jumpers at all cause only one HD. Now if I reboot
and it wont advance not sure what to do next. Any suggestions?? One other thing. I previously had 2 hds in this computer. Is there some type of residual memory or something.. I seem to remember on other computers the CMOS needs to be cleared. How does one go about doing that, or am I just making garbage up and I dont have a clue as to what I am doing??? Thanks to all who respond.

Coleco

P.S. 8200 dimension, 3.06 cpu, 1 GB HD, audigy 2, basice ATI 128 card, etc.
  • shesagordie

    12 Elder

    •

    46017 Posts

    467

    0

    Posted August 24th, 2005 20:00

    Coleco.
     
    Have you tried booting the system without the second hard drive connected? 
     
    Have you tried replacing the motherboard battery?
     
    How to clear NVRAM
     
     
    Bev.
     
      
  • Coleco

    53 Posts

    467

    0

    Posted August 25th, 2005 01:00

    Thanks for the reply. I will try those suggestions. That is what I was looking for, a nudge in the correct direction. I know my post was a little confusing when I re-read it. There will be only one hd in this 8200 now. A brand new WD 120 GB hd. It is only being recognized as secondary hd 0 in the bios and I cant get past error, try f1 or f2 for set up. Thats what I am trying to say. I will replace the battery and try to clear NVRAM. Thanks again!!
  • shesagordie

    12 Elder

    •

    46017 Posts

    467

    0

    Posted August 25th, 2005 01:00

    Coleco.
     
    A hint, the primary C: hard drive is "HD 0", the secondary hard drive is "HD 1".
     
    Bev.
  • Coleco

    53 Posts

    467

    0

    Posted August 25th, 2005 02:00

    Thanks shesagordie,
    My inital black screen says primary hd 0, primary hd 1, secondary hd1 not detected. In the bios, secondary hd 0 is found and the other 3 options dont show any hd. However, with windows xp in the cd it doesnt go any further. I cleared NRAV without any sucess. Tomorrow I can try to change the batteries. This comp is about 3 years old. Thanks.

    Coleco
  • Coleco

    53 Posts

    467

    0

    Posted August 27th, 2005 18:00

    Well,

    Installing new mb battery, clearing NVRAM and trying multiple different cables all result in the same problem. Secondary HD 0 recognized and the other 3 arent (primary 1 and 0, secondary 1). Now the question is why are there 4 options at all in the bios? There is only one hd I am putting in this and it is brand new. Shouldnt it be detected as HD 0 or primary 0 or something like that? Why 4 options unless again there is some mb memory. Meaning, I previously had 2 HDs in the 8200 and both of them are gone, with the new WD 120 GB attempting to be installed. I am wondering if there is a defect in the mb (over 3 years old now) or the new hd. I know it is regestering with the EDE cable and there is power to it (it hums when connected). Any other thoughts. Previously, I have never had a problem like this. Pop a new hd in and away you go assuming the jumpers were set o.k. with master/slave etc. I keep thinking when I turn on the computer it will go right into the installation xp screen but it doesnt. It stops at error press f1 or f2. I changed the boot order to cd first and I see on the screen that it says cd or dvd not installed?? Any suggestions??
    Coleco