UNSOLVED

bubernak

updated

22 years ago

B

bubernak

6 Posts

0

21316

February 17th, 2005 17:00

Adding second hard drive to new 8400

I just purchased a new 8400 with an 80 GB hard drive and I'm interested in adding a second hard drive.  Are there some instructions somewhere on the DELL web site that describes the installation of a second drive and how to set up the RAID configuration properly.  I read that the 8400's come with a RAID controller built in, so I'm assuming I only need to purchase the drive.  Finally, is there anything in particular I should be looking for, i.e. speed, buffer size, drive size, when shopping for a drive, or do I just need to make sure its SATA?  I've added hard drives into previous PCs, but never in a RAID configuration.  Any help/instruction would be greatly appreciated!  Thanks,  Mike
  • ejn63

    11 Legend

    •

    87469 Posts

    •

    321256 Points

    357

    0

    Posted February 17th, 2005 17:00

    Ideally, you need a drive of the same make and model that you already have. At a minimum, you need a drive the same size - if you pair, say an 80G with a 160 in RAID1, you'll get a total of 80G; as RAID0, 160G - not 80+160 or 240 (i.e., the smaller drive controls the array).

    You'll need a data cable if you buy a bare drive (they usually come with retail drive kits).
  • wayneskid

    1 Rookie

    •

    17 Posts

    357

    0

    Posted February 17th, 2005 18:00

    I have a similar situation.  My new Dim. 8400 has a 160GB Seagate SATA drive and I'm adding another drive of the exact same model.  The system is running Win XP Pro.  My question is, is it best to install the new drive, boot up and let Windows find and configure the drive?  Or, should I use the Segate DiscWizard utility.

    BTW - my new drive did not come with a data cable of any kind.  I'm hoping I can buy one today at CompUSA rather than go through the delay of ordering the cable from Dell.  Dell's order process should tell you you need to order a cable seperately, IMHO.

  • TomXPS

    1310 Posts

    357

    0

    Posted February 19th, 2005 00:00

    If your setting up RAID, no need to do anything with the drive outside of installing it.    On boot up open the control panel and double click Intel Application Accelerator.   Select the option to migrate a drive to RAID.   Select the orginal drive SATA port (usallly 0) and then it will ask for a RAID array name, and the type 0 or 1.    Some where it will ask the disk SATA port on the drive to add to the array this will be the new one you just installed.    The migration will start running, you boot once or twice and your done.  

    If your setting up RAID 0, you have 50% the size of the two disk to create another partition.    Uset the disk manager to create another partition, and format it.

     

  • wayneskid

    1 Rookie

    •

    17 Posts

    357

    0

    Posted February 19th, 2005 01:00

    TomXPS........Thanks,

    This is going to be a non-RAID install.  Do you suggest just plug it in, boot up, format and I'm done?

  • TomXPS

    1310 Posts

    357

    0

    Posted February 19th, 2005 03:00

    Yes that about it.   I think the SATA port is already enabled so it sould auto detect.   Just partition and format it and your done.   May want to change the drive letter of your CD so the new HD is "D".

     

     

  • wayneskid

    1 Rookie

    •

    17 Posts

    357

    0

    Posted February 19th, 2005 05:00

    I assume the SATA port is enabled since Drive C is the same drive model as the new one I'm going to install.  Also, I gather there are no jumpers or anything since it's SATA?  The PC now has a CD RW as D and a DVD RW as E.  You're saying I should change them both; to E & F.  Do I do this before I install the new SATA drive?  How do I do this?
     
    A curiosity: why does Dell have you move the existing (only) hard drive from the upper bay down to the lower bay and install the new (second) drive in the upper bay?
     
    Thanks for being so helpful.

    Message Edited by wayneskid on 02-19-2005 01:23 AM

  • TomXPS

    1310 Posts

    357

    0

    Posted February 19th, 2005 15:00

    Have no Idea on why they want you to move the drive.    May be a old documentation, that was carried forward. when they had IDE drives where you shared the cable.  

    Should not make any difference when you change the drive assignment.  Acutally just recommened it.   If you have some CD applictions that expect the drive to be "D" or "E" then maybe leave well enough alone, and let the new drive be "F".   Just my perfence to have all the hard drive partitions ordered.    Usually on my system I move the CD to "X" and "Y" when I first re-install.

  • mecasey67

    5 Posts

    357

    0

    Posted February 19th, 2005 19:00

    Sorry for jumping in but I'm having trouble adding a second SATA drive to my 8400. The bios sees the new drive but XP does not, not even in the admin drive setup area. Any suggestions? THanks!
  • TomXPS

    1310 Posts

    357

    0

    Posted February 19th, 2005 20:00

    I think it already enabled as Dell ships them, but if you have to change the BIOS setting you do it with F3  on power up.  Dell calls it Setup.   I may be wrong on the F3, since I do not change it that offen.   But on my XPS I had to do nothing special to add the Second drive to my system in the Setup.   (BIOS).

     

  • bubernak

    6 Posts

    66

    0

    Posted February 21st, 2005 11:00

    I’m still a little confused with the RAID thing…what’s the difference between RAID 0 and 1?  In my situation, my 8400 came with an 80 GB drive and I’m looking to add a 160 GB secondary drive, so it sounds like with RAID 0 I’d lose half the new drive size in order to mirror the 80 GB of my primary drive and do I end up with just a single drive letter “C”, as opposed to a “C” and “D” drive?  Is a RAID 1 configuration somehow different from that, or does the 0 and 1 just refer to the two drives?  And finally, if I do a non-RAID installation, are they completely separate then, and I end up with two drive letters?  As you can tell, this is my first PC with this type of capability, and I just want to make sure I understand it before I purchase and install a second drive.  Thanks, Mike