Daily Heartbeat Health Check fails while GUI reports all global servers/ports
connected
Prior to the last update to 5.34.00.16, our daily health check reported everything healthy except Heartbeat through 8443. Note: Site Specific addresses and serial numbers have been removed.
Following the upgrade the daily health check only reports two heartbeat failures - 443 and 8443, no other detail and no footer to the email.
When I check via the console, all servers are reporting connected on all ports. All services except esrswatchdogservice are running.
Has anyone seen this before and have any idea how to fix it?
I found the relevant steps to add a device in SCG. After entering the VxRail Manager IP address, please follow the steps below to complete the device setup and connectivity validation.
Steps to Add or Reconnect the VxRail Device in SCG
Navigate to Devices → Select "Add Device" (or locate the existing device (Exsisting device name ) if it is already listed.
Device Type: Ensure you select the correct device type — for VxRail, this is typically listed under "VxRail" or "Hyperconverged".
Enter Credentials:
IP Address / FQDN: You have already entered the VxRail Manager IP — confirm it is correct and reachable from the SCG appliance.
Username & Password: Enter the VxRail Manager admin credentials. These must be current and valid.
Test Connectivity: Once the IP and credentials are entered, click the "Test Connection" or "Validate" button to verify that SCG can successfully communicate with the VxRail Manager.
Complete the Setup: If the connectivity test passes, click "Save" or "Finish" to complete the process.
If the Connectivity Test Fails
Verify Credentials: Confirm the username and password are correct and have not expired or been changed recently.
Check Network Reachability: From the SCG appliance, confirm you can ping or reach the VxRail Manager IP.
Verify DNS Resolution: Ensure the SCG appliance can resolve the VxRail Manager FQDN (if using FQDN instead of IP).
Firewall/Port Requirements: Ensure ports 443 and 8443 are open between the SCG appliance and the VxRail Manager, as well as outbound to Dell backend servers.
The Daily Heartbeat Health Check email shows false failures on ports 443 and 8443, even though the GUI correctly reports all global servers and ports as connected. It is not a real connectivity problem.
If the GUI is green and devices are connecting, the gateway is healthy.
If you want this officially confirmed or corrected, you will need to contact Dell Support and open a service request, as the fix requires a backend bug confirmation, patch, or guided remediation from Dell.
DELL-Erman O
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
From the shared images, it's clear that the Device 'VSPEXBLUE' was facing a connectivity issue which triggered an alert email. From the latest image collected on August 13th, it seems the connectivity issue has resolved as the number of devices in the category, "Success with Warning / Not all features enabled" is 0. However, in case the alert is still reporting disconnected devices, Kindly check if the device "VSPEXBLUE" is in healthy state. This alert can be triggered due to multiple reasons:-
- Device credentials in SCG are outdated.
- DNS resolution issues exist between SCG and the device.
- Device IP/FQDN has changed.
- One of the managed components is unreachable.
You may test the connectivity to the device page for the device "VSPEXBLUE". If issue persists, refresh the page or attempt Remove/Reconnect for this device.
From the shared image, the 'erswatchdogservice' service is in 'Running' status which means its operating normally.
For any follow up queries, Please share the Make and Model Number of the device "VSPEXBLUE" and share full page screenshots wherever possible for better clarity.
Dell-Jai S
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
I have this device show up. I entered the VxRail manager IP into the box and that's all i can do. Any step can provide? Or any reference guide? thank you!
Dell - Ramkumar R
Moderator
•
3 Posts
•
11 Points
0
0
Posted August 18th, 2026 08:11
Hi @Hubert Wu
Thank you for the update and the screenshot.
I found the relevant steps to add a device in SCG. After entering the VxRail Manager IP address, please follow the steps below to complete the device setup and connectivity validation.
Steps to Add or Reconnect the VxRail Device in SCG
If the Connectivity Test Fails
I also found a relevant video reference that demonstrates a similar process for adding a device to SCG - https://www.dell.com/support/contents/en-id/videos/videoplayer/add-a-single-device-in-secure-connect-gateway-virtual-edition/6281590474001
Reference Documentation
For detailed guidance, please refer to the following Dell Support resources:
Please refer to the following troubleshooting guide for SCG.- Secure Connect Gateway — Virtual Edition Troubleshooting Guide | Dell US
Dell - Ramkumar R
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
Dell - Ramkumar R
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!