I purchased HP EX900 SSD, 500 GB, M.2 PCI-e NVMe, and after installing it to my Dell precision tower 5810 it is not detected in BIOS nor in Windows 10 Disk management.
After reading another posts on forum, I've:
upgraded bios to version: Dell Inc. A34, 19. oct. 2020
turned RAID to off, is set as AHCI now
disable secure boot
I'd love to hear any other solutions about how to correctly set up or enable NVMe.
Since it looks like I can not edit my original post, I am adding, that my primary disc is Samsung SSD PM871b, which has Win10 installed on it. New HP NVMe is my secondary disc, I don't need to make it as bootable, I would like to access it as just another disc inside Windows.
For a NVMe SSD (that fits into a M.2 slot on motherboard) there is usually a special section in the BIOS that shows it. First step is to get it to appear there. It can-not appear in Windows, if it is not appearing in BIOS first.
If it was new, it should already be raw/blank/un-initialized. If not, you can make it that way with a proper "DiskPart clean" procedure. Be very careful with this command (as it is easy to instantly erase ANY drive in system).
But even if it isn't, I don't think that would prevent it from appearing in BIOS (especially with SecureBoot disabled). So, refer back to first paragraph in this post.
If it is used (or even if new) might just be a bad SSD.
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired) - Like many of you, I can appreciate a good game-engine. - I answer questions here, but I'm not a Dell employee. - Consider giving posts you like a "thumbs-up" - Posting models-numbers and software versions speeds trouble-shooting. - Click "Mark as Accepted Answer" on any post that answers your question best.
That is fine. However, I don't think it changes what you need to do.
It is a little unusual for a machine to have TWO M.2 slots on the motherboard that both allow NVMe SSDs to be installed into them.
I'm not real familiar with T8510, or what optional disc controllers you might have installed. I can read manuals though. I hope you have already examined manual and it says you can actually install a 2nd NVMe SSD where you are trying to.
Back to the BIOS. If you can install TWO NVMe SSDs in this machine's motherboard, you should see both locations in BIOS. With only the Samsung-SSD installed, you would see it, and then the empty slot. Of course, a special controller would have different look, general procedure, etc. It might not even show in BIOS.
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired) - Like many of you, I can appreciate a good game-engine. - I answer questions here, but I'm not a Dell employee. - Consider giving posts you like a "thumbs-up" - Posting models-numbers and software versions speeds trouble-shooting. - Click "Mark as Accepted Answer" on any post that answers your question best.
It is brand new, I have bought 3 pieces for multiple computers in my office, and no one of them is working so I guess it has nothing to do with bad sticks.
Do you have any advice, how to make it appear in BIOS? I was looking and playing in BIOS but can not find any suitable option, that's why I decided to ask for solution on forum.
@Chino de Oro these are images of my BIOS (sorry for bad quality). Under Device Information only Samsung SSD 2.5 inch is detected. I also added picture of Primary Video Slot as you requested. I'm not sure about which slots 1/4/5 slots on motherboard are you talking about. Can you refer to the motherboard image/screenshot I've added in my previous post (NVMe is currently plugged into slot 6. on that image).
Sorry, my mistake, I did not give you right information. Samsung SSD is actually 2.5 inch, and is placed in optical-drive cage, as it should be.
NVMe, I'm trying to install is currently plugged to slot number 6. from manuals I've pasted below (PCIe x16 slot (PCIe 3.0 wired as x8) (slot 1)) using PCIe adapter.
@willJ , we just posted at the same time again. If you check and it doesn't show up in slot 1, shut down the machine and try slot 4 or 5 (as marked on motherboard). This process will eliminate the possibility that you have a bad adapter.
@willJ , pictures or screenshots are not showing up yet. When you install NVME SSD to PCIe slot, in BIOS, it will detect as mass storage under Primary Video Slot (Table 6). Refer to the manual on page 31 for motherboard info and slot naming. The slot number I referred to are imprinted on the motherboard along each slot if you look carefully. I suggest to try other slots in case it does not show up in slot 1 in BIOS. If you try and none of the slots are shown with mass storage, you have a bad PCIe adapter.
Hi @Chino de Oro, maybe we added comment at the same time. I installed it to slot number 6. from manuals (PCIe x16 slot (PCIe 3.0 wired as x8) (slot 1)) using PCIe adapter.
willJ
1 Rookie
•
7 Posts
4195
0
Posted January 11th, 2022 23:00
Since it looks like I can not edit my original post, I am adding, that my primary disc is Samsung SSD PM871b, which has Win10 installed on it. New HP NVMe is my secondary disc, I don't need to make it as bootable, I would like to access it as just another disc inside Windows.