UNSOLVED

ChmpT

updated

15 years ago

C

ChmpT

6 Posts

0

41194

January 27th, 2012 05:00

Best way to connect and route traffic between PowerConnects at two sites for Streched Hyper-V cluster.

Hi,

I'm trying to come up with the best way of connecting two PowerConnect 6224s in our primary site to a 5524 at our disaster recovery site to facilitate network traffic across a stretched/multi-site Hyper-V cluster.

Our primary site consists of two Dell Hyper-V hosts connect to an Equallogic PS4100X with two stacked 6224 switches. I am planning for our disaster recovery site to have a single Hyper-V host connect to a single EQL PS4100X and a 5524 switch. The traffic that will need to go between the sites is EQL SAN replication, cluster heartbeat and general/public network traffic. Each has a VLAN tag.

The two sites are several miles apart and have WAN connection solely for this traffic in the form of a Etherlink, which essentially gives us a standard RJ45 socket at both sites. This is logically a passive link with no routing or VLAN configuration.

One idea we had was to in the primary site to have a SFP fibre optic link from each 6224 plus a fibre optic link for general network traffic connect to a new 5524 in the primary site and then connect this new 5524 to the disaster recovery site's 5524 via that single site-to-site etherlink. We can see how this give us physical connectivity, but we're unsure how to ensure traffic get routed across properly, considering it's only a single connection to each switch. We're looking a VLAN routing on the switches but can we have multiple VLAN routing configured on a single SFP port? Any suggestion or pointers on the best way of doing this will be greatly appreciated. I've also attached below a basic picture of our network layout without the additional 5524 at the primary site.

Many thanks.

 

  • ChmpT

    6 Posts

    3152

    0

    Posted January 30th, 2012 01:00

    Thanks for your response, DELL-Daniel Co.

    So, this is basically adding your typical static route. Which is no problem, however, this single fibre connection will need to route traffic for three separate subnets, each in its own VLAN. Using a static route would mean assigning an IP address to the SFP port for th fibre link so that it can act as a gateway. Can I add more than IP address to this port and thus create a route for each subnet?

  • 3152

    0

    Posted January 30th, 2012 12:00

    Have you tried looking into having a PowerConnect 6224 at your DR site as well and then do VLAN routing between the sites?  I have multiple sites connected via MPLS and have at least a PowerConnect 6248 routing VLAN traffic via OSPF which makes life very simple.  Depending on the number of VLANs you want to route at your Main and DR sites may constitute you looking into using OSPF to dynamically create your routing table.

    This is just a suggestion but I always took the approach on segregating each remote network behind a true Layer3 device because PowerConnect 55XX is very limited in its static routing capabilities and does not support dynamic routing protocols.

  • ChmpT

    6 Posts

    3152

    0

    Posted February 2nd, 2012 02:00

    Thanks for your reply randy_kuga. Our network will require the routing of three separate subnets, on three separate VLANs through a single port across a single wired link. Are you saying the the PC 55xx series do not support OSPF routing?

  • ChmpT

    6 Posts

    3152

    0

    Posted February 2nd, 2012 02:00

    DELL-Daniel Co, I fully understand configuring the routing table on each router to allow the proper routing of traffic. I can easily set up a port for each of the three subnet and vlans, configure them with the relevant IP address and use a port for routing each vlan. What I trying to do, or ascertain whether it's even possible, is to have each of the three subnets configure to route through just one port on the switch connected to our site-to-site cable.

  • 3152

    0

    Posted February 2nd, 2012 09:00

    ChmpT, the PowerConnect 55xx does not support dynamic routing protocols such as RIP or OSPF.  You can only use static routes which can be an administrative nightmare as your network grows.

  • ChmpT

    6 Posts

    3152

    0

    Posted February 2nd, 2012 09:00

    randy_kuga, that's good to know. However, as this netwrok infrstructure is just for clustering and iscsi traffic, we will only ever have the three static routes, so not an issue. Just need to ascertain if I can configure three disctinct routes on one physical port.

  • ChmpT

    6 Posts

    286

    0

    Posted February 6th, 2012 01:00

    We'll be steeing this up next week, so I'll update this posting once it's completed.