UNSOLVED

Azul Israel

updated

23 years ago

Closed

0

17512

April 29th, 2004 02:00

USB/Serial Adpaters & DataCAD Security Hardware Key

I recently purchased a new Dell Inspiron notebook and installed DataCAD 8 version 8.05 for Windows 95/NT.  The installation process was successful, however the notebook is unable to accommodate the Hardware key as the notebook is not furnished with a parallel port, however it is furnished with two (2) USB ports
 
In light of this I have subsequently purchased and assembled USB/Serial Portable Adapter, Gender Changer and Serial Port Adapter to allow for the use of the Hardlock.  This solution proved unsuccessful.  Can you offer any solutions which will allow me to use my current software. 
 
Please find below a list of specifications of Dell note book and peripherals to assist you with your assessment.
 
DELL NOTE BOOK
  1. Inspiron 1100, 14.1 XGA, Celeron 2.4 GHz
  2. 256MB, 1 DIMM, Inspiron 1100
  3. 30GB Ultra ATA HArd Drive for Inspiron
  4. Microsoft Windows XP Home Edition

PERIPHERALS for Hardlock

  1. Belkin USB/Serial Portable Adapter
  2. Belkin Serial Port Adapter DB9 Female/DB25 Male
  3. Belkin Gender Changer Adapter DB25 Female/Female.
  • DELL-Corey

    1 Rookie

    •

    2570 Posts

    687

    0

    Posted April 29th, 2004 17:00

    Azul Israel,

    This is not too helpful, I know, but personally, I don’t think you are going to be able to get this to work on that system.
  • 687

    0

    Posted April 29th, 2004 19:00

    Thanks Dagrizz:

    I will take your suggestion and attempt to get the USB equivalent of the doggle.  Already the software manufacturers suggested acquiring an upgrade, as the lastest versions of the software have USB Hardware keys, however that option is out of my budget. Failing this I will have to return the laptop.

    Thanks again.

     

  • dagrizz

    34 Posts

    687

    0

    Posted April 29th, 2004 19:00

    This is an issue that more and more users are going to run up against.

    If yuo are using any kind of high end CAD software, most of them require some sort of protection scheme.  This is either a parallel port, a serial port, or new software might accomadate a USB dongle.

    I use a lot of different Printed Circuit Board  design packages that all require a parallel port that is by directional and uses a dongle.  The proble that I found with the usb to (your port here) is that they are not usually designed with this in mind.  They only provide communications in a single direction.

    There are a couple of potential solutions:

    1) Contact the CAD software vendor to see if you can get a USB dongle and drivers for the package that you are using.   They may charge you a small fee for this.

    2) If your notebook has a network conection you can again contact yuor software vendor to see if they offer a license file tied to your network interface card.  Again there may be a small fee for this.

    3) If you are with in the 30 day grace period on this computer from DELL return it and get a laptop that has the prerequisite ports that you need.

    Note to any heavy CAD users out there:

    When you are doing your home work on a system to buy look at all of your needs.  If you know before hand that you will need bidirectional parallel ports, check to make sure that the system you are considering has them.  Dont assume that they will.  As these systems mature, the manufacturers are removing the older legacy ports.  Supposedly nobody needs them any more as all of the devices that used them are now USB comaptible.  This is a mistake on the manufacturers part. 

     

  • 687

    0

    Posted April 29th, 2004 19:00

    Thank you Cory

    Do you have any suggestions or solutions to my problem. Is there any other hardware/peripherals I can purchase to attempt to use the the parallel port Harware key?