UNSOLVED

aharris680

updated

20 years ago

Closed

0

19981

July 11th, 2006 22:00

Inspiron 700m speaker wires cut by hinge

Hi
 
I have an Inspiron 700m and the speaker wires have been cut by the screen hinge.  The laptop is out of warranty and I have seen that this is a problem with the 700m.  Does anyone have any idea how I can fix this?
 
Thanks
Alan
 

Message Edited by aharris680 on 07-11-200606:58 PM

  • 592

    0

    Posted July 12th, 2006 02:00

    Thanks.  I also managed to solder mine back together.  The hinge on mine had messed up 2 of the wires, so I had to add a short piece to each.
  • horsehead

    5 Posts

    592

    0

    Posted July 12th, 2006 02:00

    Today I found the same exact thing happened to my 700m. I was just about to post a similar message, but now I'll just reply to you!

    I was also out of warranty, so I had nothing to lose but to try and fix it myself. It took me a while to figure out what the problem was. Everything was working perfectly up until about 2 weeks ago, when suddenly the sound from the laptop speakers stopped working. The headphone jack still worked, so I knew the soundcard was fine. For a while I assumed it was a software issue, and tried checking and unchecking all the mutes and changing all the levels and everything I could think of. Even trying a linux live cd (knoppix). Nothing worked so finally I said, "What the hel l, I'm looking inside." Since the only thing I could think of was that the speakers were somehow unplugged. 'Reseat the speakers' is what I think the diagnosis is. It was pretty easy to get to the affected area, as the speakers plug in to the motherboard underneath the keyboard. Really you just need to get the hinge cover off and you would find where the speaker wires are cut, just like the subject says. It is the oddest thing. Pulling the keyboard back, you can see where the wires plug in to the motherboard.

    I have some pretty good soldering skills and am a bit fearless (overly so), so I was determined to fix it myself. I totally clipped all 4 speaker wires, not that it needed much clipping as the hinge did most of the work itself. There are 2 black and 2 white wires. I made sure to note which wires were originally connected so as not to cross them in the reconnection. Maybe not obvious since they were clipped to begin with, but I think I got it right. One by one, I carefully stripped a small amount off each end of the wires.

    It was kind of a pain in the but t to do on the monitor end, since the wires were very short and close to the speaker. I partially disassembled the display to get better access. By removing the bottom right rubber nub and screw underneath, and then popping a few of the brackets apart under the speaker and along the right side, I was able to get inside the monitor area where the right speaker sits a little better.

    There was just enough extra speaker wire near the plug to pull back a small amount to allow the bare wires to overlap. I only stripped about 2-3 millimeters from each clipped end. I thought about just twisting the wires together but it was a bit awkward to get in and do that, so I pulled out the soldering iron. It was easy enough for me to do this, but I was sure to be VERY CAREFUL not to get the hot iron too close to (or touching) any plastic parts. A small amount of solder now connects the two bare ends of each clipped wire, reconnecting the circuit. If I had access to some, I would have grabbed some heat shrink tubing to put over each soldered connection to isolate them from one another and anything else, but I used electrical tape. It seemed to do the job just fine, but it was a little cramped putting all the wires (and electrical tape) back under the hinge cover. I reduced the amount of electrical tape I used and was able to fit everything back together. Now my speakers work again!

    Good luck. Don't try this at home. Call Dell first and see what they tell you. I'd be curious to hear what they say.
  • The_Shark

    2 Posts

    592

    0

    Posted August 20th, 2006 03:00

    I was thinking of just replaceing the wire that goes into the Motherboard (no big deal). I have not seen anything about howto disasemble the screen.  Any help would be great.

    I also have another problum that the system does get a little hot that burns the index finger of the touch pad or the bottem of the notebook gets to hot.  Any idea’s what might be cuaseing this? 

    I do not have the recall batterys. The old power addapter was getting well over 110 degrees that dell has replaced it.  If the new power adapter doses not resolve the heat problum, what else can it be?  is their any software to tell me the temperature of the inside of the notebook?

    What is a safe processor to put into the 700m notbook?

     

  • djenry

    2 Posts

    592

    0

    Posted September 1st, 2006 16:00



    @The_Shark wrote:

    I was thinking of just replaceing the wire that goes into the Motherboard (no big deal). I have not seen anything about howto disasemble the screen. Any help would be great.

    I also have another problum that the system does get a little hot that burns the index finger of the touch pad or the bottem of the notebook gets to hot. Any idea’s what might be cuaseing this?

    I do not have the recall batterys. The old power addapter was getting well over 110 degrees that dell has replaced it. If the new power adapter doses not resolve the heat problum, what else can it be? is their any software to tell me the temperature of the inside of the notebook?

    What is a safe processor to put into the 700m notbook?




    Same problem with my 700m. Unfortunately out of warrenty as well. Never thought about cutting all the wires and attempting to resolder all of them. I foolishly tried to solder them while the wires were still connected to the screen. It wasn't until afterwards I found a manual on how to dismantle the keyboard;/
  • loooney2ns

    17 Posts

    592

    0

    Posted September 16th, 2006 16:00


    @The_Shark wrote:

    I was thinking of just replaceing the wire that goes into the Motherboard (no big deal). I have not seen anything about howto disasemble the screen. Any help would be great.

    I also have another problum that the system does get a little hot that burns the index finger of the touch pad or the bottem of the notebook gets to hot. Any idea’s what might be cuaseing this?

    I do not have the recall batterys. The old power addapter was getting well over 110 degrees that dell has replaced it. If the new power adapter doses not resolve the heat problum, what else can it be? is their any software to tell me the temperature of the inside of the notebook?

    What is a safe processor to put into the 700m notbook?






    Mine was getting very hot too. Try cleaning out the fan-it tends to collect dust and animal hair. I pulled a huge clump out and now it's cool again! The screen is easy to take apart. Remove the 6 round rubber bumpers and the screws underneath. Remove the flat cover to the left of the wi-fi indicator and the screw underneath. Unsnap the bezel. I found it easier to work from the inside (screen side) with my fingers and work all the way around. To remove the speakers, unscrew them along with the LCD inverter. The whole thing took about 15 minutes including unscrewing the keyboard to unplug the wire from the motherboard. Now the problem is that one of the wires is broken off right at the speaker. I'm looking for a replacement set.
    I guess one speaker will be better than none for now.

    Message Edited by loooney2ns on 09-16-2006 06:14 PM

  • rough2000

    17 Posts

    592

    0

    Posted January 16th, 2007 00:00

    I have sent the following to the Consumer Product Safety Commission about the broken speaker wires. I you are having the same problem you may want to do the same. www.cpsc.gov

    I have a Dell Inspiron 700m laptop computer. The speakers are in the upper part of the computer with the display.  The wires to operate the speakers run through the hinge that connects the display portion of the computer with the lower (keyboard & motherboard) portion of the 700m. Through the flexing of opening and closing the case the wires have broken. These wires are in a position where they could touch the metal hinge and this would then electrify some external parts of the computer. I am concerned that this could cause electrical shock, or if the wires became shorted there may be a chance of fire. I am concerned that this is a safety hazard.