
Solved!
Go to SolutionDell M.2 / NVME Specifications And Upgrade Requirements For Latitude, XPS, Precision Mobile and Optiplex
Good day Dell Community,
Because of your questions I'm pleased to present the below information, specifications and requirements for M.2 on various Dell models.
Precision 7710 | 7720:
Maximum internal dives supported: 3
Drive configurations supported ( max ) : (3x M.2) or (2x M.2 and 1x 2.5inch SATA)
PCIE Lanes:
The 2 M.2 slots available are wired as 4X
The 2.5 Inch bay is wired as 2X
Parts needed to install M.2 into the dedicated M.2 slot:
1x HR8P8 thermal cover ( comes with cover and thermal pad )
1x 4270E Screw: ( Holds the cover down on top of the M.2 drive )
Parts needed to install an M.2 into the 2.5 inch bay of 7710 and 7510:
1x 745TM 2.5 inch metal bracket - most units will have this already included
1x Y1WJX M.2 bracket ( goes inside of 745TM )
4x 2864D M3X3 screw. Most systems will have these already included. These screws hold in the Y1WJX M.2 drive carrier, or a 2.5 inch drive into 745TM.
1x WPTND M.2 Interposer Board. This installs into Y1WJX M.2 bracket.
5x 4270E M2.0*3L screws
1x HR8P8 M.2 thermal cover
Find instructions here on the Dell Community.
Precision 7510 | 7520:
Maximum internal dives supported: 2
Drive configurations supported: (1xM.2), (1x2.5 SATA) (2xM.2) (1xM.2 and 1x2.5 SATA)
PCIE Lanes:
M.2 slot supports 4X
The 2.5 Inch bay is wired as 2X
Parts needed to install an M.2 into the 2.5 inch bay are the same as the 7710 above.
Precision 5510 | 5520 and XPS 9550 | 9560:
Maximum internal dives supported: 2
Drive configurations supported: (1x M.2) (1x 2.5 SATA) (1xM.2 and 1X 2.5 SATA)
PCIE Lanes:
M.2 slot supports 4X
The 2.5 Inch bay is wired as SATA
Parts needed in order to install a M.2:
1x 88DJK
thermal pad ( no plate required )
1x 4270E
M2X3 screw
Parts needed in order to add a 2.5 inch drive:
1x XDYGX cable
2x 3XYT5 rubber side isolator
1x 3FDY3 metal HDD bracket ( some units may already have this installed even if a 2.5 inch drive wasn't ordered from Dell originally )
Discussed here on Dell Community.
Precision 3510:
Maximum internal dives supported: 1
Drive configurations supported: (1x M.2) or (1x 2.5inch SATA)
PCIE Lanes:
M.2 slot supports 4X
2.5 Inch bay is wired as SATA
Parts needed to upgrade from 2.5 inch drive to M.2 drive:1x X3YR8 M.2 end bracket
1x 1X2MT thermal cover
2x 4270E M2X3 screws
Discussed
here on SpiceWorks.
Precision 3520
Maximum internal dives supported: 2
Drive configurations supported: (1x M.2) (1x 2.5inch SATA) (1x M.2 cache drive and 1x 2.5 inch drive )
PCIE Lanes:
M.2 slot supports 4X
2.5 Inch bay is wired as SATA
Parts needed to upgrade from 2.5 inch drive to M.2 drive:
1x 2FFR0 end bracket
1x X3DN4 -Thermal plate
1x 4270E - End screw
Latitude E5270 | E5470 | E5570:
Maximum internal dives supported: 1
Drive configurations supported: (1x M.2) or (1x 2.5inch SATA)
PCIE Lanes:
E5270 supports 2X
E5570 with H processor supports 4X
E5570 with U processor supports 2X
E5470 with H processor supports 2X
E5470 with U processor supports 2X
2.5 Inch bay is wired as SATA
Parts needed to upgrade from 2.5 inch drive to M.2 drive are same as 3510 above.
Latitude 5280 | 5480 | 5580:
Maximum internal dives supported: 2
Drive configurations supported: (1x M.2) (1x 2.5inch SATA) (1x M.2 cache drive and 1x 2.5 inch drive )
PCIE Lanes:
5280 supports 2X
5580 with H processor supports 4X
5580 with U processor supports 2X
5480 with H processor supports 4X
5480 with U processor supports 2X
2.5 Inch bay is wired as SATA
Parts needed to upgrade from 2.5 inch drive to M.2 drive are same as 3520 above.
Latitude E7270 | E7470:
maximum internal dives supported: 1
Drive configurations supported: (1x M.2)
PCIE Lanes:
M.2 slot supports 2X
Parts Needed in order to upgrade to M.2:
1x DJ69P thermal cover
2x 4270E screw M2X3 ( most systems will have at least one of these already included )
Discussed
here on SpiceWorks.
Latitude 7280 | 7480:
Maximum internal dives supported: 1
Drive configurations supported: (1x M.2)
PCIE Lanes:
M.2 slot supports 2X
Parts Needed in order to upgrade to M.2:
1x R6TGF thermal cover
2x VJYP9 screw M2X3 ( most systems will have at least one of these already included )
XPS 13 9350 | 9360
Maximum internal dives supported: 1
Drive configurations supported: (1x M.2)
PCIE Lanes:
The M.2 slot available supports up to 4X
Parts needed:
1x 4270E screw M2X3XPS 13 9365
Maximum internal dives supported: 1
Drive configurations supported: (1x M.2)
PCIE Lanes:
The M.2 slot available supports up to 4X
Parts needed:
1x 4HP13 - Thermal plate
2x JPRFM - M1.6x2.5 screws
Optiplex 5040 | 7040 ( Mini Tower ) :
Maximum internal dives supported: 2
Drive configurations supported: (1xM.2) (2xM.2) (1xM.2 and 1x2.5) (2x2.5) (1x3.5)
PCIE Lanes:
The single on board M.2 slot supports up to 4X
The M.2 drive installed into the 2.5 inch bay: 2x
Parts needed for M.2.
On-motherboard M.2 bay:
1x R7HGK
thermal pad ( installs onto the motherboard under the M.2 drive )
1x
YYJF8 screw M2X3.5
2.5 inch bay with M.2:
1x 6J3FV SATA cable
1x X9FV3 M.2/2.5 inch bay adapter/caddy
On motherboard M.2 installation instructions found here.
Optiplex 3050 | 5050 | 7050 ( Mini Tower ) : :
Maximum internal drives supported: 2
Drive configurations supported: (1xM.2) (1x2.5) (1x3.5) (2x2.5) (1xM.2 and 1x2.5) (1xM.2 and 1x3.5)
PCIE Lanes:
The single on board M.2 slot supports up to 4X
Installing M.2 into the 2.5/3.5 inch bay is not supported
Parts needed for M.2:
1x DHR6X spacer (goes between the motherboard and M.2 drive)
Installation instructions found here
Learn how to reset drives to non-Optane here
OS install notes:
There's an updated storage driver (IRST F6) to include PCIE support. ( The one you have to install for Windows to see the drive during installation ) :
Also see: Installing Windows 7 on a SKYLAKE system using MDT: http://www.dell.com/support/article/us/en/19/HOW11493/en
Obtaining an ISO image:
For some systems you can obtain Dell operating system images through Dell Hosted image
Note: not all systems and service tags will have an image available for download.
Note: Even though Dell Hosted Images have USB3 drivers slip streamed in, they may not include the IRST driver at this time. ( some may know this at the F6 driver ). As a result you may need to install the IRST driver manually during the Windows install process.
Dell is currently working to add the IRST driver to the Dell Hosted Images. No ETA on when this will happen at this time.
Discussed here on SpiceWorks.Other M.2 Articles:
Imaging M.2 Solid-State Drives in Intel Skylake chipset systems
Only 1 Solid State Drive (SSD) seen on Interposer card
SSD not detected on startup or reboot on New Precision 15 5000 (5510) or XPS 15 9550
PXE Booting with M.2 Solid State Drives
How to distinguish the differences between M.2 cards
Why am I unable to find option in BIOS to set a hard drive password on NVMe SSD
Responses (136)
Solutions (0)
@Saltgrass,
Please note that I'm not an expert on drive performance but I have my statement for you below:
It's my understanding that the number of lanes is a separate specification from the actual throughput speed supported by any one model. Example: 4X throughput from say a E5570 may be different from the 4X throughput speed on a Precision 7710. When I submit my questions to Dell engineering they're not related to throughput speed and historically, Dell does not give out exact throughput speeds per model.
@Markus15,
Thank you for your kind feedback. Yes, I plan to get more information on the new models in the near future. Below is what I have so far for your 5580
2FFR0 - M.2 frame ( clip on the end )
X3DN4 -Thermal plate
4270E - End screw
@JimAtLaw,
I wasn't able to get exact technical detail on the RAID behavior. However, the assumption is that the two 4X drives will run at the same performance as the 2X drive it's grouped with in the RAID 5. Same goes with RAID 0 and RAID 1.
As to your class 50 question: Drive classes and lanes are considered separate. Class 50 drives have slightly better performance than a class 40 drive. Class 40 and class 50 drives can work with either 2 lane support for 4 lane support. In other words a class 50 drive will have slightly better performance on a 2 lane port when compared with a class 40 on a 2 lane port. Same goes when you have 4 lanes and comparing performance between class 40 and 50.
Hope that makes sense.
@ItdirectorFLLP,
I had the previous document I linked deleted. I now have a new document that is more clear regarding M.2 BIOS password support. Here: www.dell.com/.../no-bios-to-set-a-hard-drive-password-on-nvme-ssd
I will add it in to the original post.
@DKasparov,
I went back to Dell engineering and they confirmed that there are physical limits on the Vostro 5468 motherboard that only allow support for M.2 SATA. I've reported this fact to the documentation team and the NVME support claimed in the user's guide is going to be removed.
@cs42,
I will work on getting a better answer on the caching but it will take some time. I should be able to have the answer in a couple weeks, probably in the form of a brand new document outlining scope of support and the technical aspects all in one place.
Greetings Raphaeljr,
Dell only supports M.2 2280 and 2.5 inch drives with the E5270. I have no documentation that would say for sure that a drive will work in the WWAN slot. It's likely the 2242 size for the WWAN slot. You'd have to try it at your own risk to find out for sure.
Greetings Griffsters,
Thank you for your question and interest in the 5580.
It's very rare for Dell to adjust any system firmware in order to limit a system to below NTFS or GPT standards. I have no reason to believe that a firmware limit has been set on the 5580. Even when the user's guide says 512GB max.
I pulled up my internal customization page and my internal parts replacement page and each reflects maximums of 512GB drives. This means that Dell simply hasn't, and currently does not sell the 5580 with a 1TB M.2. This does not mean that the firmware does not support drives that are over 512GB.
I suspect that Crucial has tested this by physically installing a 1TB M.2 drive and found that it worked for them. Now can I guarantee any one 1TB drive will work? No. You'll simply have to try it at your own risk. It's my firm opinion that most 1TB M.2 drives will work with the 5580 however.


Justin C
6 Operator
•
783 Posts
141111
1
Posted October 20th, 2016 09:00
Greetings Ypyap,
Thank you for your question.
Yes, the Vostro 14 5468 does support M.2, according to my documentation.
You'll need:
1x 3P44J M.2 bracket
2x 7CJG4 M2*2 screws ( I'm still confirming if this the correct part number )