UNSOLVED

BizBomb

updated

24 years ago

Closed

B

BizBomb

13 Posts

0

55555

December 26th, 2002 17:00

Dell Latitude CPxH and PIIIM 650 w/ Speed Step

I recently purchased a PIII-M 650 CPU with speed step (MMC2 Package) and installed it in my Latitude CPxH and it will only run at 500mhz and is not propery recognized in the bios. I have the most current bios revision installed in the CPxH. I am also a PC tech and have the service manual for the CPxH and noticed the the motherboard for the CPxJ is the same part number. The latest bios revision does support speed step for the CPxJ. Now of course there is not any "supported" way of getting around this, but is there any way to force the CPxJ bios flash onto the CPxH? If so, does anyone think this would help the new CPU work at it's potential?

  • dthrax

    2 Posts

    464

    0

    Posted December 27th, 2002 10:00

    The CPU is probably running at 650 and the system is mis reporting it. I've seen this on a several machines. I believe the fix was actually a BIOS flash and video driver. Then download Intel's proc testing tool and test in the OS once you have the video driver installed.
  • BizBomb

    13 Posts

    464

    0

    Posted December 27th, 2002 12:00

    Thanks for the reply. The latest Intel CPU id utility (ver. 4.61) reports the CPU running at 500mhz and expected 500mhz. The Intel microcode utility as well as inspection verifies that the CPU is definitely a PIII-m 650mhz with speed step. The latest Bios for the CPx-H is installed (A-14) as well as the latest video drivers from Dell's download section. I have not tried the video drivers from ATI. Any additional suggestions would be appreciated.
  • patniven

    5 Posts

    464

    0

    Posted December 27th, 2002 18:00

    There is a command line switch to force a BIOS image to flash, even if it is not the correct image file.  But first, are you certain that the Mobo part numbers are the same for a CPxH and CPxJ?  I thought that SpeedStep was a hardware enabled option on a CPxJ motherboard, not a BIOS programming issue.  If it is simply a BIOS flash that enables it, then use the switch /jabil after the filename of the "J" BIOS that you will use. The switch works as advertised...I know, I destroyed a CPtC board a few days ago by forcing a CPxJ BIOS into it.  Of course, my mistake was that the video cards are completely different on the CPtC and CPxJ, and the reason that it won't boot is probably because of the wrong video BIOS.  Good Luck!  Keep us 'Posted'...;)

     

  • BizBomb

    13 Posts

    464

    0

    Posted January 2nd, 2003 12:00

    Thanks for the reply. The "Speed Step Technology" hardware is built into Intel's MMC2 Package. The wonderful marvel of Intel's "MMC" packaging is that all the hardware is included to support the product (such as the North Bridge Chipset). I will definitly check my part numbers before attempting to force the flash. I just don't know for sure what will happen. The only difference in the two motherboards is a slightly different ESS chipset for the audio. I'am 100% possitive that the video is identical. If I do flash, can I still flash back to the other BIOS as long as the system powers up and the default boot device is FDD? I was told that as long as those two things are pressent, that a flash back to a known good BIOS is not a problem. I will keep everone posted after I double check the part numbers.
  • Laptopsetc

    1 Message

    464

    0

    Posted February 16th, 2003 03:00

    I was wondering if you ever got the 650 Mhz to work with the CPxH?  Did the CPxJ bios work?  Please let me know what you did because I am very interested! DC
  • JersWork

    770 Posts

    464

    0

    Posted February 16th, 2003 18:00

    From what I can recall from the experiences of others:

    THe CPxH BIOS with the 650 MHz processor will cause the CPU to run at the lower "SpeedStep" speed (500 MHz?).

    The CPxH will run with the CPxJ BIOS,  but it will report the incorrect audio controller,  and possible video controller.  I know the audio controller was different between those two models,  but I am not sure about the video controller.  If you go this route,  it supposedly the SpeedStep will function properly allowing the system to run at the full 650 MHz with that processor.

  • stonent

    2 Intern

    •

    823 Posts

    464

    0

    Posted February 17th, 2003 00:00

    They both have original ATI mobility video chips in them. But the sound chip is correctly detected in windows.
  • BizBomb

    13 Posts

    464

    0

    Posted February 17th, 2003 13:00

    Thanks for the reply,

         I haven't had the guts to try and force flash the Bios yet. I was waiting on some more imput. After reading these recent posts, I will give it a try later today. Assuming that I can still boot up and get online, I will post the results later. If I cannot get I re-started or re-flashed, you can expect some anxious posts on how to remedy the problem.

         Thanks again for everyone's imput.

     

                                                                             Bizbomb...

  • BizBomb

    13 Posts

    468

    0

    Posted February 18th, 2003 15:00

    !!!!!!!!!!!!!!!!!!!!!!!!!!Success!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

     Thanks for everyone’s input. Everything worked fine, with the exception of the line out on my docking station. I can live with that though. My CPU is now running at 650Mhz and I am even considering upgrading to a PIII 850. Even the video appears to be faster.
     I force flashed the Dell CPx-H BIOS with the CPx-J BIOS version A15 using the /JABIL switch and everything just fell right into place. It was definitely a very tense 45 seconds waiting for the flash to complete though.
     Some advise to anyone reading the forum thread. Please be very careful. My laptop could just as easily become a vegetable. Some tips that can help you determine if this option is possible for your PC are; do your homework on your hardware and similar model’s hardware (The Dell service manual is a good place to start.) to see what compatibility may exist, be prepared for whatever may happen, it is a gamble and you can destroy your PC, make sure your BIOS is set to boot to the FDD by default before you begin, prepare two floppy disks, one with the BIOS your are flashing to and another with the working BIOS, make sure the working BIOS floppy disk is configured to force flash the BIOS automatically and unattended (If your flash fails, this may be the only way you may be able to recover.).
     Thanks again for everyone’s help. I wouldn’t have been able to have such success with out you. Good luck to everyone.
        
                                                                                           Bizbomb… 

  • BizBomb

    13 Posts

    363

    0

    Posted February 27th, 2003 16:00

         The 850mhz CPU is also an Intel Speed Step CPU. The research I did indicated to me that this is where the Lattitude CPx-J maxed out at. So, this should be the max speed of the CPx-H as well when it is flashed with the new BIOS.

         I will certainly be willing to give you any guidence that you like. The whole process can be a bit un-nerving. Good luck with finding one at a reasonable price. I was able to find some on E-bay that ranged in price from $189 - $400.

                                                                               Have Fun,

                                                                                               Bizbomb