
UNSOLVED
B
berryhedgehog
21 Posts
0
93935
December 21st, 2014 11:00
Installing Corsair cooler on Aurora R4; can't control the fans
Aurora R4, Windows 8.1, everything is updated to the latest versions
My stock pump failed. First I tried air cooling (Cooler Master 212 Evo), and it didn't fit by approx. half a centimeter due to the component sticking out above the CPU.
Then, I bought the Corsair H80i system, which was highly recommended on these forums. It comes with a USB to the motherboard. The device manager would only show it as an "unrecognized device" and couldn't find drivers. I tried all the ports on the motherboard and a cable to the back as well; it didn't work. It ran, but I couldn't control the fans: they just ran max speed the whole time.
The store associate told me to try exchanging for a Corsair H75, which is about the same but no USB cord. I also can't control the fans on this, either through Command Center or through various versions of Corsair Link. Corsair Link does show the fans running max speed but can't change them. Command Center shows the wrong number entirely. I uninstalled Corsair Link, and that didn't help. I know that you need the 7pin adapter to show the pump properly, but the fans should be showing up fine, right? They are 4 pin fans with a Y-cable joining them. I have them plugged into SYS_FAN and the pump itself plugged into CPU_FAN. I haven't seen a single BIOS error the whole time. Also, the Y-cable looks like it's missing a pin; I don't know if that might be affecting it, but I think the H80i cord was fine and it still didn't run.
Responses (16)
Solutions (0)
the #1 topic of today will be if I helped crapp-out your cooler Berry, by telling you to plug your pump into the mthbrd fan header. The answer is no. I have unboxed my AMD Asetek cooler, I have plugged it into that header, I have not asked you to do something I would not do myself & my pump runs as we'd expect it to. I do not know what is wrong with your system today, before or after I made my post above. It is possible an actual pin inside your pump's connector is not making contact. Otherwise it should work from any header you plugged into: sys-fan, cpu- fan, memory fan, mthrbrd-fan. 12volts & ground is all it needs, 12volts and ground are what they tend to supply. A fan header is a fan header.
I assumed your y-splitter was missing the 4th pin, which is the pwm signal. It is missing the tach pin, therefore it is assumed to be proper inside of Aurora. While pump's connected to cpu-fan header, as is recommended here, perhaps jiggle, feel the pump head for signs of life, making sure not to keep pc on too long of course.
berryhedgehog
21 Posts
2035
0
Posted December 21st, 2014 14:00
Was set to Active, I checked. I tried moving things around, and now I think the pump stopped working. Btw the fans and y-splitter are 4pin; the pump is 3pin; both say in the installation instructions they can connect to 3- or 4-pin. Results:
Original: y-split sysfan + pump cpufan = in HWMonitor fans at 3.5k rpm, cpu temps 30C
fan sysfan + pump cpufan = command center shows 18k rpm, can't control
fan sysfan + pump motherboard = cpu fan failure error, cpu temps 80C in HWMonitor
fan motherboard + pump cpufan = command center shows cpu fan 0rpm, cpu temps 80C in HWMonitor
fan cpufan + pump sysfan = making printer sounds, cpu temps 90C in HWMonitor
y-split sysfan + pump cpufan (original) = cpu fan failure error, cpu temps 100C in HWMonitor
y-split cpu_fan + pump sysfan = cpu temps at 100C in HWMonitor, wouldn't shut off, had to hold power button
Tried original one more time after writing this up, same result. Dang, at least it ran before.
Plugged fan(s) did spin each time.
berryhedgehog
21 Posts
2035
0
Posted December 21st, 2014 14:00
The pin that is missing on the y-split cable is the one that goes into one of the fan connections, not the light strip.
berryhedgehog
21 Posts
2035
0
Posted December 21st, 2014 15:00
You are saying the missing pin should not affect anything?
I tried jiggling the pump connection to cpufan while on, and it did not show up on HWMonitor. Temperatures rose 50C to 60C in the meantime.
I'm not sure what you mean by the second post, connecting a fan to the ports. Aren't they all in use in order for the system to run, or there are more I haven't tried? I apologize, I'm not very knowledgeable on this, and I don't think I have the spending money to take it to a professional for repairs.
I only exchanged the H80i for the H75 yesterday, so I could take it back to the store and return it. I just really want this to be over, as it's causing me a lot of stress.
what I know is that you have two fans there, even your old stock fan. While your system is running you can be plugging a fan from one header to another looking for the sweet spot if it exists today. I describe 90-120 second tests in the event your pump is being stubborn and not running, which does not help here.
berryhedgehog
21 Posts
2081
0
Posted December 21st, 2014 16:00
Thank you for your time; of course I do not expect help 24-7. You have been very kind to help me as much as you have. I was pressing on various connections to make sure they're tight, and the cord you told me in my previous thread is the media card reader fell out... I'm not sure where the other end goes now. I'm sorry; this is something I should know before asking complex questions.
I am not online 24-7, I apologize. Well, I understand you are frustrated. Before you came in here today you hooked your system up using the proscribed methods to no avail.
By now we should all be aware that the Aurora mthrbrd would live out a natural life separate & apart from the master i/o board, which is to say, Corsair would have told you to plug into your mthrbrd cpu-fan then told you to plug your fan(s) into a chassis fan header for normal operation & it should have worked as it does on one million other mthrbrds on the market Aurora no different. You used the proscribed method: fans to sys-fan pump to cpu-fan @ the top light strip to no avail, a repeated statement.
A 30c (86f) temp while fans are at full blast is perhaps a clue. My 4820 right now sits at 26c (77) w/fan rpm's only @ 1200. Your temps seem higher than mine, even at full blast. Are you sure your pump head was seated correctly from the very beginning?
In my 2nd post, your top light strip, for instance you could have disconnected mem-fan: the trial would be to find any header willing to run your fan(s) @ a low speed, since you said the sys-fan header simply put your fans @ 4000rpm's, an untenable situation there & here for us as no one else appears to have a bit of new advice. Were you to have a pump that will run, it does not explain why the proscribed method did not originally work.
What we know is that the master I/o board takes the fan signal directly from the mthrbrd (red circled area), perhaps calculates a better curve, whatever, then relays it to the radiator fan through the top sys-fan header. It cares not if a pump is attached at the 7pin. The output should have been proper at sys-fan. I speculate now if one of your pins is not making contact (red circled area), or, were one to trace that harness back to the master i/o board if it is seated properly there too. If it is, I would try the dissipation fix: unplug pc, hold top power button down one minute, let rest 5 minutes, plug back up, pwr on. See if the master I/o board, which we do assume is still in charge of fan speed, 'settles the fans down', in the 2 minutes you do your test. Perhaps make sure your top light strip '24-wire harness' is also properly seated up top & @ master I/o. I will wait to hear back, yours may be a situation of returning your h75 in exchange for new & starting all over again. Where in the meantime, I and others sit back and go hmmmmm: why didn't the proscribed method work for Berry right out of the gate.
(Corsair expects you to run push-pull off that y-splitter as designed. Had it been missing the pwm pin, then yes, it is unacceptable for use in Aurora. The missing pin affecting anything is testable: if when correct fan speed is restored to one fan, pop your splitter on, if same low speed then splitter is a charm as they've included it in your package to be)
You can upload pics (500kb size limit) to your post:
yes side ways
You would remove your video cards, remove your black pic-e fan assembly (unplug pci-e fan) to reveal your mio & its wiring, trace your mio harness that connects to the mthrbrd (red circled we talked about), trace your top light strip's harness. Properly seated at the mio you are looking at. This is my pic, I can not tell what is what in my own computer Berry. Trace your wiring & ensure they are both seated. A maneuver like this would come of course if with a new cooler or yours there now confirmed (running pump), a working cooler, you can not get correct fan speed using the proscribed method we mentioned. To me it is an indicator but that is me Berry and what I would do, go to these lengths. I would need confirmation my top light strip and red circled connector are secure at both ends, since I know the mio board is what ties them to the sys-fan header & ultimately to the fan and its dictated fan speed.
Were you to chime into solved!!! right now you would note there are 50 subscribers to it, 50 people getting an email message you are here in the forum seeking help & advice. I expect not one of them is in the forum right now, but may have a minute to think your situation over anytime between tonight and tomorrow, so it ain't just you n' me going at it like this. If we get no where I suggest you make a duplicate in solved!!! so that the real firemen can help put out this fire for you. I am new to Aurora, never done a swap, and all ya got at the moment. heh heh. My ego can take it only if you get the help you need.
berryhedgehog
21 Posts
959
0
Posted December 21st, 2014 19:00
http://i.imgur.com/vrSHUge.jpg
On my phone it doesn't give me the option to insert a photo. It seems that the pink circle is the motherboard thing you had me try to plug the pump into earlier, and the orange circle is the light strip, judging by cord colors. They are firmly in place.
I spoke with a Knowledge Center employee at MicroCenter tonight. He says he's installed an H80i on an Aurora before. He said to try with only the pump connected to sysfan and listen if it's working or use the BIOS to check. I don't know how to check in the BIOS, but I didn't discern the sound of it working and it was still showing 90C - 100C in HWMonitor. I will try and ask some of my coworkers if anyone can help me carry this beast into my car, as I can't lift it alone. I'll just let the MicroCenter people enjoy this torture, and I'll pay up what it takes.
And it was me that messaged you regarding the 7pin adapter; I didn't realize that was also you.

Cass-Ole
8 Professor
•
1874 Posts
•
9716 Points
2035
0
Posted December 21st, 2014 12:00
from solved!!! page one, they give you the outline
you could try removing the y-split, run one fan from sys-fan. If no good, I believe I would back the fan header off (red circled) & try to plug my pump in there. A one minute test, see what's what.
if no good, stay plugged into red circled area header, try one pwm fan plugged into open cpu-fan. If no good, plug pump back into cpu-fan (circled blue), plug fan into red circled fan header. Musical chairs. One minute tests. I prefer my cooler keep the alienhead on it, & haven't done a swap-out yet for something else. try these qwik tests, wait for more informed help in the meantime.
In Windows under power options, make sure active cooling policy is checked if win8.1 has that.
It is possible you need a 4-wire 4pin y-splitter. The 3-wire 3pin (in a 3+1 connector) is probably to blame. Stop using y-splitter, test w/one fan.