UNSOLVED

noxomnia

updated

2 years ago

N

noxomnia

1 Rookie

•

4 Posts

0

490

April 27th, 2024 15:13

Dell Latitude e6420 bricked after changing boot mode from Legacy to UEFI. This is ridicolous

My dell latitude e6420 got bricked after changing the boot mode from Legacy to UEFI. I am stuck at the dell logo, no way to go forward or to use the options

I tried to:
swap rams,
change rams,
remove the cmos battery, wait (even days) and put it back in 

Tried pressing fn while its booting

Tried pressing D while its booting

Remove the battery pack and use the charging cable only

Nothing works.

Now i understand that this is an old pc, but it's absolutely ridicolous that you can mess it up by changing a stupid setting. I searched on the internet and this is a commun issue appartenly, even on the e6520

  • JOcean

    11 Legend

    •

    12621 Posts

    •

    69453 Points

    1

    0

    Posted April 27th, 2024 16:13

    Have you tried changing back to Legacy. With a system as old as the 6420 it might be a good idea to replace the CMOS battery, a pretty easy job.

    I am not a Dell employee...I am forum volunteer

    Serious work on an E5430 and constantly building and working on an i5-6500 Desktop

  • noxomnia

    1 Rookie

    •

    4 Posts

    1

    0

    Posted April 27th, 2024 19:29

    @JOcean​ that's the problem, it's bricked, i can't change it back to legacy

  • JOcean

    11 Legend

    •

    12621 Posts

    •

    69453 Points

    1

    0

    Posted April 28th, 2024 00:49

    @noxomnia​ Have you replaced the CMOS battery as I recommended?

    I am not a Dell employee...I am forum volunteer

    Serious work on an E5430 and constantly building and working on an i5-6500 Desktop

  • noxomnia

    1 Rookie

    •

    4 Posts

    2

    0

    Posted April 28th, 2024 09:44

    @JOcean​ not yet, i've ordered it

  • JOcean

    11 Legend

    •

    12621 Posts

    •

    69453 Points

    2

    0

    Posted April 28th, 2024 14:34

    @noxomnia​ Let us know how that turns out. My wife has an E6420 and I had to replace the CMOS battery to correct some problems she was having. 

    I am not a Dell employee...I am forum volunteer

    Serious work on an E5430 and constantly building and working on an i5-6500 Desktop

  • noxomnia

    1 Rookie

    •

    4 Posts

    1

    0

    Posted May 1st, 2024 12:47

    @JOcean​ did not work. the bios is corrupted. absurd, all of this for changing a single setting

  • Bonez0r

    1 Rookie

    •

    1 Message

    •

    2 Points

    2

    1

    Posted June 26th, 2024 13:12

    What if you follow the procedure that you would normally use for a BIOS upgrade? That should hopefully overwrite the corrupt BIOS and replace it with the downloaded one.

    BIOS files can be downloaded here: https://www.dell.com/support/home/en-us/product-support/product/latitude-e6420/drivers (choose "system BIOS" as download type). They are .exe files. Since you can't boot your OS, you'd have to make a bootable ms-dos usb drive, then boot from that and execute the downloaded file.

  • rupe01

    1 Rookie

    •

    2 Posts

    •

    2 Points

    4

    1

    Posted August 5th, 2024 03:24

    Have you tried holding the Ctrl and Esc keys? Worth a try. You've probably seen it, but the procedure is here: https://www.dell.com/support/kbdoc/en-us/000132453/how-to-recover-the-bios-on-a-dell-computer-or-tablet

  • Suzuki365

    1 Rookie

    •

    1 Message

    •

    3 Points

    1

    1

    Posted October 16th, 2026 14:04

    So I know this is an old post, however I was able to fix my E6520 with the same problem that bricked my laptop when changing legacy to UEFI. So here is what I did. It was a little involved but not hard at all. So I bought a CH341A EEPROM BIOS Programmer https://www.amazon.com/dp/B0BYSRSZPC?ref=ppx_yo2ov_dt_b_fed_asin_title. And what you have to do is remove the bottom cover, unplug the CMOS battery then upright the laptop and remove the bezel from around the keyboard and remove the keyboard screws and remove the keyboard. Then remove the palm rest. Instruction https://www.parts-people.com/blog/2016/08/31/dell-latitude-e6520-p14f001-palmrest-touchpad-removal-tutorial/?srsltid=AU7gw4WYp8Qanm0IRm2Chipn4_d0RN2cP3a83DJgfkUu1XjlVZAMYKqU

     

    Then locate the 2 BIOS IC chips https://www.badcaps.net/forum/troubleshooting-hardware-devices-and-electronics-theory/troubleshooting-laptops-tablets-and-mobile-devices/99177-dell-latitude-e6520-bios-location

     

    Now the one on the left should be marked U52 (8 Megabyte IC chip) and the one on the right should be marked U53 (2 Megabyte IC chip)

     

    Now comes the fun part. Don’t be alarmed it’s not hard. So you need to clip the CH341A EEPROM BIOS Programmer onto each chip aligning the red ribbon wire to pin 1 of the chip denoted by a dot on the top corner of the IC chip and download each chips software, Be sure to name each .bin file as per each chip U52 or U53 using asprogrammer https://github.com/therealdreg/asprogrammer-dregmod/releases and install it on another laptop. Watch this video he will show you how to hook it up. https://www.youtube.com/watch?v=Jqzp0729u_I

    Once hooked up you should see a bright red light meaning its powered up. In the video he will also show you how to configure Asprogrammer to work with the CH341A EEPROM BIOS Programmer. Just pay attention because you have to select what programmer you are using and the number of the chip itself. Take a picture of the chips with your phone and zoom in to see the numbers. Once set up what I did was downloaded each chips firmware 2 times comparing the size to make sure everything is good. And don’t forget to name each download to each chip, remember they are different size megabyte IC chips. Once I downloaded each chips firmware * Make sure to DOWNLOAD FIRST and save VERY IMPORTANT* I went and erased IC chip then uploaded the saved firmware back into the chip. I started with the 2 meg chip first. That is just the way I done it. Not sure if it matters what chip you do first. You can decide which way to do it whether 8 meg or 2 meg first. If it doesn’t work then try a different way. Once I did that my laptop started working again.... Like I said DONT BE ALARMED. I know it looks like a lot but all my typing is me trying to be as clear as I can to make it easier for you. I would also say is to watch as many videos as you can to see and get familiar with this process. Remember it is not hard. I looks hard becuse you never done it before. That is what I did to learn the process.Good luck!!!!!!!!

    (edited)