PS6000: Firmware upgrade Failure from V5.0.8 to V6.0.7
I have two old Storage PS6000 and PS4000. 2nd one updated successfully from V5.2.11 to V6.0.7. But the PS6000 is not updating from V5.0.8 to V6.0.7 and showing error "You cannot upgrade to this version because of compatibility issues, Update aborted". Both the storage are not in production so before doing upgradation I made them factory default though failure !!
I have also tried upgrade to 7.0.1 but couldn't so then tried to V6.0.7 and PS4000 upgraded but not the another one.
I need to keep both the storage in same version and group. Could you please help me in this regard.
If you read the upgrade docs carefully you will find the info from which version you can upgrade to the latest or if an intermediate version is needed. Upgrade your 5.0.8 to 5.2.x first and than to 6.0.7.
Now iam confused because you told us that you upgrade both of your units which indicated that both array are part of the same group or they run on different groups.
Merging of groups is not possible so in this case you must evacute/delete the member from the group. Deleting a member that all data is ereased and it reset back to factory defaults.
If you have both members in same group already you have to place both in the same pool and check if "enabled Loadbalacing" in the group settings. This will allowed that a volume spreads over multible members. The volume overview will tell you how a volume is distributed.
I would like to mean that I have to separate storage in there default setting (so they are in there own group and own pool ). more pool can be created under a group. I want to add another one member under a pool.
For Example: PS6000's Group name is CIG and has 2 pools: Defaults and pool1. Its own member is under "Defaults" pool. Now I like to add PS4000's member under "pool1".
Yes it is possible... BUT the PS4000 must first removed from its group which means all data would be lost because the unit will be deleted from the group and reset to factory defaults. All data, network config and password will be ereased!
Adding a unit to a existing group is a 60sec. job when you ...:
- hook up the serial to the active controler module
- knowing the group password
After 60sec. the unit will be visible in the group manager and the wizzward will ask you in which pool to place the new member and which raid level you would like to use. Dont forget to configure the rest of the network interfaces.
I have made Factory Default and then not configured any single thing in the PS4000.
Then I have hooked up the serial cable from PS4000 active controller module to PS6000 Active Controller module but after waiting 60sec or more I have not seen anything to enter password or any wizard like you said.
Have I tried as you said or any mistake or any other solution please ??
I have a question is that without any configuration after Factory Default setting of any storage will it be able to be attached within another storage group?
Aeh..... you have to hook up the serial between your Laptop/PC and the active controllermodul and not between the both members. So use putty.exe or winxp hyperterm or what ever your favorite programm is. The settings are industry standard 9600,8,1,n.
On the login prompt use "grpadmin" as user and "grpadmin" as password. The setup wizzard starts automaticly. You will configure eth0 with a IP from your iscsi range and the wizzard when the tool ask for the groupname use the already existing one and you will see that it discovers the group ip automaticly and ask for joining.
If you dont like this commandline voodoo there is also a windows programm which i only use once years ago. So i cant remember to its name but it make a broadcast to discover all units. Please be 101% sure that when using the windows programm you select the right array and not the production one!
If you dont get it we can do a teamviewer session later this day. Just send a pm.
Origin3k
6 Operator
•
2424 Posts
•
12408 Points
2267
0
Posted February 10th, 2014 23:00
If you read the upgrade docs carefully you will find the info from which version you can upgrade to the latest or if an intermediate version is needed. Upgrade your 5.0.8 to 5.2.x first and than to 6.0.7.
Regards,
Joerg