UNSOLVED

MacAddict1

updated

19 years ago

M

MacAddict1

29 Posts

0

5858

September 17th, 2007 03:00

Changing the management IP of an AX150 already in production

Hello all,

I was wondering what is the correct procedure for changing the management IPs of a CLARiiON AX150 that is already in production. I tried changing it during our "patching downtime" but it gave me pretty scary messages:

1) I tried using the Navisphere Server Initialization utility but it told me that since it was already initialized, I was unable to change it.

2) I went to "http://currentIP/setup" but then it told me that it first had to be disjoined from some sort of "domain". It didn't make any sense to me so I stopped at this point (didn't want to loose the data).

Is there a way to change the IP once it has been setup? Or do I have to re-initialize the whole thing (losing virtual disks, etc)?

Thanks,
MacAddict
  • houndfish

    53 Posts

    834

    1

    Posted September 17th, 2007 07:00

    Go to

    http://www.emc.com/products/systems/clariion/ax150/support/support.jsp

    Service & Support
    Frequently asked Questions
  • MacAddict1

    29 Posts

    834

    0

    Posted September 17th, 2007 07:00

    It said that I need to unitialize the system. Will that delete all the data?

    Mac
  • houndfish

    53 Posts

    834

    0

    Posted September 17th, 2007 07:00

    No, see also KnowledgeBase Article EMC112056

    "Uninitialize the array. This resets security settings. Data will remain untouched and accessible."
  • De La Soul

    112 Posts

    834

    0

    Posted October 9th, 2007 18:00

    Dude, just use these easy steps, no need to go to setup page.

    Power down the AX150 and then power it back up holding the power button in for 4 seconds. Remember, hold it in for four seconds and then release it.

    Let the AX150 power fully up and then run the initialization wizard. Once you run it you can change the IP address and administrator password if needed. Now if you miss the 4 seconds or don't hold it in long enough when the AX150 boot, just shut it down and try again until it becomes unitialized.

    Remember, this does not delete data and only changes the IP and administrator settings. All you virtual disks are still there.

    Tootles,
    Woodsta
  • 834

    0

    Posted February 1st, 2012 14:00

    Hi Guys, I tried all these and it still doesn't re-initialize. What to do?

  • christopher_ime

    6 Operator

    •

    1962 Posts

    834

    0

    Posted February 4th, 2012 21:00

    http://powerlink.emc.com/public/ax150/en_US/faqs/AX_FAQs.htm

    Click on "How do I change the storage system management IP address(es)?"

    This provides slightly more detailed steps than mentioned above.

  • 834

    0

    Posted February 6th, 2012 13:00

    Thanks for ur response.

    The problem I am having is uninitializing the array. I have tried the procedure reinitialization procedure several times without luck. According to thios article, http://en.community.dell.com/support-forums/storage/f/3412/t/19371198.aspx ,If the first 4 drives are not emc supplied, the array is uninitializable. Is that correct? I am not sure about the drives and even the order they are installed. Thanks

  • kelleg

    6 Operator

    •

    4537 Posts

    834

    0

    Posted February 6th, 2012 13:00

    This is the AX100, but the layout of the OS disks (where the flare is stored) is the same as the AX150. The first four disks across the top, 0-3, contain the operating system for the array. The physical disk sectors are formatted at 520 instead of the normal 512. This means that you can not use off-the-shelf disks. You must get replacement disks from EMC. In addition, the OS on the first four disks are specific to the slot when configured - once a disk is in its slot, you can not move it to another slot.. If these are not the original disks that came with the array (OS disks), then the array will not function properly (will not boot).

    AX100_disk_layout.JPG

    glen