UNSOLVED

Templar1988

updated

2 years ago

T

Templar1988

1 Rookie

•

14 Posts

0

2125

February 10th, 2024 00:30

Aurora R15, fastest ram this motherboard can support?

Hey guys, newbie here so go easy but my R15 showed up last night and I am simply loving it so far! But I would like to change out the stock 4800mhz Ram to something that is faster and also has RGB. I am looking at the Corsair Vengeance 2x16GB since there are only 2 slots on the motherboard. My question is what is the fastest ram this motherboard can support? I am running the i9 13900KF for a processor, I read somewhere that 5600mhz is the fastest? And that I’ll need to enable XMP in the BIOS correct?

(edited)

  • Vanadiel

    8 Professor

    •

    7094 Posts

    •

    29695 Points

    0

    0

    Posted February 10th, 2024 03:09

    Only OEM memory is guaranteed to work.

    These systems are legendary for poor aftermarket RAM support.

    See this FAQ for supported memory: R15 FAQ

    Be aware they are OEM, and different than retail Kingston Memory

  • btf3072

    1 Rookie

    •

    42 Posts

    0

    0

    Posted February 12th, 2024 11:01

    I tried a whole bunch of DDR5 modules.

    T-force Delta DDR5 7200mhz / CL34 is the one that worked best for me (ff3d532g7200hc34adc01).

    Runs at 7000mhz / CL34.

  • Templar1988

    1 Rookie

    •

    14 Posts

    0

    0

    Posted February 13th, 2024 08:34

    @btf3072​ 

    Did you have to change anything in the bios to allow access to the max speed of the ram? I called dell and they advised all ram is pinned at 4800mhz unless it’s dell exlusive Kingston ram which can go up to 5600mhz. I did go ahead and purchase the rgb corsair vengeance ram that I wanted at 5600mhz but alas it is showing it running at 4800mhz in awcc

  • LikeHerdingCats

    1 Rookie

    •

    59 Posts

    0

    0

    Posted February 16th, 2024 17:24

    I explored this too and got a lot of "can't be done" from Dell and some intriguing responses from users, that said it could be done and a few firmware tweaks, which sort of scared me off.

    I bought 5200 speed ram since I needed more (from 32 to 64) in my system.  I've seen there are some other memory modules that "seem" to run faster (somehow) - but again, I was worried a future firmware update would undo any gains.

  • Vanadiel

    8 Professor

    •

    7094 Posts

    •

    29695 Points

    0

    0

    Posted February 16th, 2024 17:29

    @LikeHerdingCats​ That is a good worry to have, because on some other systems firmware updates have caused issues with aftermarket RAM in the past.

    Memory support is unfortunately one of the weak points of these systems.

  • GraemeWilly

    1 Rookie

    •

    25 Posts

    0

    0

    Posted April 11th, 2024 21:18

    I'm solid on Kingston Renegade 6000Mts, 38, 38, 38, 76. I can't get my Kingston to run the advertised cl32 but this is good enough and noticably better than stock.

    I also tried Tforce 7200Mhz but even given the higher numbers and lower latency it just didn't seem as snappy as my Renegades at cl38 and I didn't notice better frames and I did see some referenced memory errors with those, namely only at shutdown. I decided to keep the Renegades and will re-research this when memory becomes a bottleneck which it is not right now at 240 FPS in Halo Infinite, for example. With stock memory (5200Mhz) I'm about 10-12 frames off.

    Dell loves to use slooowwwww memory in their high end PCs, then charge you $300+ for a bump up to slightly faster memory (5600Mhz Fury Beast) at $165 per 16GB module. They should call themselves Apple because that's what Mac desktops have always done: offer little options and at an astronomical scalper's price. 

    FYI, you don't have to downgrade BIOS, if you don't wish to risk it. Just put the stock memory in and set it to RAM1 in AWCC and save/apply. When prompted to restart, opt "Later" and then shutdown and put your other memory in. Done. Works for me with Tforce and Kingston anyway and on BIOS 1.10.

    (edited)

  • StillaRebel24

    1 Rookie

    •

    12 Posts

    0

    0

    Posted July 3rd, 2024 12:36

    @GraemeWilly​ do you have the 32GB set or the 64GB set? My 64GB Renegade Fury set will only run at 5600mt/s but that was last year when I did the roll back bios trick. Maybe they updated and I can now use them at 6000? Let me know which set you have. Thanks! 

  • StillaRebel24

    1 Rookie

    •

    12 Posts

    0

    0

    Posted July 3rd, 2024 12:41

    As far as I am aware, 32GB sets (2x16gb) will run at 7000mt/s, while 64gb sets will only run up to 5600mt/s and you’ll need to do the roll back bios trick. If anything’s had changed since May of 2023, I’m not aware of it. 

  • Artifakt

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    1

    Posted August 3rd, 2024 02:58

    @btf3072​ did you have to downgrade the bios to get it to run at 7k?

  • fseminario

    1 Rookie

    •

    5 Posts

    •

    2 Points

    0

    0

    Posted August 11th, 2024 00:17

    Based on hours of trial and error and what the dell / alienware manual states was tested to work on r15 is:

    5600 mts at 64 GB.

    Some folks say you can go higher like 6000 or 7000 with 32 GB but I didnt test those. I managed to get Kingston Fury 64 GB 5600 mts with bios 1.0.5 and awcc v6. I discovered that awcc 5 was not keeping my xmp profile so lost hours trying to get it to work on it. It worked right away with awcc 6. In awcc just go to overclock tab, then custom and choose advanced tab on memory and select the ram 1 or 2 profile. For me it  was ram 1 = 5200 mts ram 2 = 5600 mts. 

    Tip: turn off ufei bios updates in the bios to prevent awcc from auto updating your bios to the latest version. 

    ps - i personally didnt want to go higher because i didnt want to run into stability issues in case something went wrong and dell finds out i have ram that is higher than what they tested.

    (edited)