MichaelFongemie

updated

13 years ago

0

4098

July 12th, 2013 13:00

VNXe 3300 10Gb Optical


Does anyone have a picture or can confirm if the SFP+ optics come with the modules?

Anyone know of any compatibility issues with the Nexus 7k (No I didn't see anything on ELab Navigator. Just looking for first hand experience)

Thanks.

  • devijb

    15 Posts

    1171

    0

    Posted July 18th, 2013 09:00

    Hi Michael,

    Here is a picture of my VNXe3300 with the dual 10Gb Optical card as it was received;

    IMG-20130718-00518.jpg

    Find below the picture of my Nexus5010 with twinax (left) and optical (right) cables; everything is working as expected: fine !

    Colombes-20130718-00519.jpg

    Hope this helps,

    Regards, Benoît

  • Leo Li

    4 Apprentice

    •

    9030 Posts

    1171

    2

    Posted July 14th, 2013 22:00

    Hi Michael,

    On VNXe 3300, there are two PCI Gen 2 x4 I/O module slots on the SP. VNXe 3300 can supports four-port 1-Gb/s Base-T copper iSCSI I/O module, the two-port 10-Gb/s optical I/O module, and the two-port 10-Gb/s copper Ethernet I/O module.


    The optical ports on this I/O module can interface at speeds of 10 Gb/s for iSCSI (Internet Small Computer System Interface) networks3. The two-port 10-Gb/s optical I/O module uses the SFP+ transceiver module. You can see the attached two snapshots.


    And for more detailed information, you can refer EMC VNXe Series VNXe3300 Hardware Information Guide .

    2 Attachments

  • 1171

    1

    Posted July 15th, 2013 06:00

    Thanks Leo for the detail but I’m just looking to confirm a couple of things specifically with the 10Gb Optical module (I’m good with everything else.) I’ve seen the hardware guide and drawings but it isn’t clear to me that the optics are included in the picture. I’m assuming so but have not actually seen a real picture of these.

    Also was looking for first hand “yes I wired these into a Nexus 7000 and ran into these requirements” comments if there are any out there. Thanks.

  • Leo Li

    4 Apprentice

    •

    9030 Posts

    1171

    0

    Posted July 16th, 2013 18:00

    Hi Michael,

    Unfortunately, I also did not find the real picture of 10Gb optical module..    But, I think we can get some info from attached snapshot as above.

    And for the "“yes I wired these into a Nexus 7000 and ran into these requirements”, I don't have any idea...

    Hope other peers can help you on this.

  • Leo Li

    4 Apprentice

    •

    9030 Posts

    1171

    0

    Posted July 18th, 2013 18:00

    Looks so cool~~

  • 1171

    0

    Posted July 19th, 2013 09:00

    Thanks Benoit and Leo.

    Much appreciated..

    Benoit,

    If you are able to share I'd also be curious if you are using for the 10Gb for iSCSI and CiFS/NFS?

    What's your layout look like for network high availability?

    Thanks again!

  • jamesrpbh

    37 Posts

    1171

    0

    Posted September 20th, 2013 04:00

    Hi,

    Sorry to barge into this thread however we have a VNXe 3300 with 10Gb I/O modules and we can't get them running.

    They are uplinked to Cisco 3130X switches with x2-SFP+ modules and we cannot get link up.

    The cisco switches report port-flaps and disables the interface. We have tested all modules and optical cables separately and can confirm that other devices are working with our SFP+ cisco modules and cannot find out what could the problem be.

    The I/O modules on the VNXe are commited and the system reports everything is healthy but the 10Gb modules are always link-down. We stuck and failed back to copper 4x1Gb copper per SP.

    Any ideas?

  • umichklewis

    4 Apprentice

    •

    1190 Posts

    1171

    0

    Posted October 9th, 2013 08:00

    If you haven't done so, please open a service ticket for this.  There are a few commands that can be run from the service console to help troubleshoot it, but I can't remember them for the life of me.

  • Schnaars

    1 Message

    1171

    0

    Posted October 9th, 2013 08:00

    Great response!

  • jamesrpbh

    37 Posts

    169

    0

    Posted October 10th, 2013 02:00

    Hi,

    We already opened one weeks ago however got no usable answers from the support.

    I sent service_data logs frequently but always was told that the I/O modules are working correctly while they were not.

    Eventually found out what the problem was and replaced all SFP modules to another make/type and all links came up.

    So now, we are happy and everything is working.

    Regards,

    Tamas