
UNSOLVED
Unable to connect to SPA/B via CS0/1 on public network
Good day,
Recently we procure a VNX5700 with dual CS.
The array was initialized and IP addresses have been assigned to both CSs and SPs.
I am able to ping/connect to the CSs however I was not able to ping/connect SPs.
CS0 - 10.117.13.80
CS1 - 10.117.83.81
SPA - 10.117.13.82
SPB - 10.117.13.83
When I ssh into CS0 and ran
#./setup_clariion -check_and_update -all
Found CLARIION(s) CKM001146010xx
Setup CLARiiON CKM001146010xx storage device...
System 10.117.13.82 is up
System 10.117.13.83 is up
Clariion Array: CKM001146010xx Model: VNX5700 Memory: 18432
Validating CKM001146010xx storage group '~filestorage'
Setup of CLARiiON CKM001146010xx storage device complete.
and Ping from CS0 to SPA
[root@MTB-VNX-056-CS0 sbin]# ping 10.117.13.82
PING 10.117.13.82 (10.117.13.82) 56(84) bytes of data.
64 bytes from 10.117.13.82: icmp_seq=1 ttl=128 time=0.190 ms
64 bytes from 10.117.13.82: icmp_seq=2 ttl=128 time=0.177 ms
From above, SPA and SPB IP addresses are set correctly.
If I tried connect to the array via CS0's mgmt port, I was able to connect to SPA/B.
(Only if connect to the CSs directly)
The network guy said I must tried set a VLAN tag on the SPs which I managed to do that via naviseccli
After I set VLAN tag on SPs' virtual port 0, no communication is possible.
Apology as I am not a netwrok guy. Only storage I do.
Please assist.
Responses (17)
Solutions (0)
I have done un-tagging on the SPs.
The network guy show me what was configure on the switch side.
Its an access vlan.
He suggest I setup a vlan tag on the CS side.
I still dont know how I am able to do that.
I couldnt find any document on setting vlan on cs
Reply you don't need tagging for CS and SP ..it's not like datamovers where you can tag to use the same NIC on different VLANs. I have two 5700, all ports are configured as access VLANs. It sounds like proxy-arp is not passing your requests through the control station to SPs. What is the output from this command:
/nas/sbin/clariion_mgmt -info
Reply Hi Dynamox
CS1 is also on the same subnet
eth3 Link encap:Ethernet HWaddr 00:1B:21:9D:60:80
inet addr:10.117.13.81 Bcast:10.117.13.255 Mask:255.255.254.0
inet6 addr: fe80::21b:21ff:fe9d:6080/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:48167 errors:0 dropped:0 overruns:0 frame:0
TX packets:227 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3300147 (3.1 MiB) TX bytes:25876 (25.2 KiB)
Memory:81a60000-81a80000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2780 errors:0 dropped:0 overruns:0 frame:0
TX packets:2780 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:158248 (154.5 KiB) TX bytes:158248 (154.5 KiB)
[root@MTB-VNX-056-CS1 sbin]#
Reply [root@MTB-VNX-056-CS0 sbin]# nas_cs -i
Host Name = MTB-VNX-056-CS0
Version = 7.0.51-3
Location = system:VNX5700:CKM001146010562007|controlStation::0
Status = OK
Standby Location = system:VNX5700:CKM001146010562007|controlStation::1
Standby Status = Info 26575634437: Standby Ready
IPv4 Address = 10.117.13.80
IPv4 Netmask = 255.255.254.0
IPv4 Gateway = 10.117.12.1
IPv6 Address =
IPv6 Gateway =
DNS Domain = VODACOMBUSINESS.CO.ZA
DNS Domain search order = VODACOMBUSINESS.CO.ZA
DNS Servers = 41.0.1.1,196.2.53.140
Session Monitor Timeout = 0 Days
Session Idle Timeout = 0 Minutes
NTP Servers =
System Time = Thu Mar 29 14:56:43 SAST 2012
Reply

dynamox
11 Legend
•
20419 Posts
•
87439 Points
837
0
Posted March 29th, 2012 05:00
can you ask him to un-tag the port on the switch and configure it as normal "access" VLAN ..also remove the tag in Navisphere.