UNSOLVED

Shaikh1

updated

15 years ago

S

Shaikh1

29 Posts

0

36512

March 21st, 2012 01:00

Powerpath and Unisphere Host Agent

Hello

Just need some clarification around installing and configuring PowerPath and Unisphere Host Agent for Windows 2008 R2 Operating System.

  1. Do I need to install both PowerPath and Unisphere Host Agent?
  2. Under Connectivity Status, when I look at the Host Name there is no Initiators entries? But they did appear yesterday and I thought I will take some time for host appear as Managed therefore left it overnight.

However, when login into Windows OS I can still see all the drives which are presented from SAN.

Any help would be greatly appreciated.

Kind regards,

Sultan

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    2106

    0

    Posted March 23rd, 2012 18:00

  • tkjoffs

    159 Posts

    2106

    0

    Posted March 26th, 2012 23:00

    1. No.  You do not need to install either.
      1. You can use non-EMC Multi-Pathing solutions, though I will say EMC is the best and easiest to configure.  This gives you native capability yo use ALUA; a good thing.
      2. The host agent is the piece that communicates the Disk/Lun/SAN details between the Host and the Array.  It is also responsible for Host Based Self Registration which is a major time saver.
        1. Be sure to use the AgentID.txt file settings to define the Host. (FDQN on one line and IP on the other)
        2. Be sure to use and Agent.config file to define the array conenctions (I find this easier to have one file pre-defined and just copy it).
      3. Your issue above is probably related to the AgentID.txt file.  Give it a try.

    You AgentID.txt file needs to look like:

    hostname.int.asurion.com

    10.10.10.10

    You will place that file in the location: C:\Program Files (x86)\EMC\HostAgent

    Once it is there, restart the host agent service. (Navisphere Agent)

    Ted

  • Shaikh1

    29 Posts

    1335

    0

    Posted March 27th, 2012 00:00

    Thanks all for your help. I going to work on PP next and will post back the outcome.

  • Shaikh1

    29 Posts

    2105

    0

    Posted March 27th, 2012 00:00

    Hi TKJOFFs,

    Thank you for responding. Are you able to post an example of agent.config file entries.

    Thanks

    Sultan

  • Shaikh1

    29 Posts

    713

    0

    Posted March 27th, 2012 01:00

    Yes it was manually registered before installing Host Agent and PowerPath software. This was done so I could install Window OS.

  • tkjoffs

    159 Posts

    644

    0

    Posted March 27th, 2012 01:00

    I can't see the connectivity status page so I cannot be sure, but with PP not showing both HBAs, that means one of two things.

    1. The HBAs (WWNs) are not properly registered (logged in and in a storage group)...
    2. The Second HBA is not Zoned in the Fiber Fabric or has no path to the Storage Array.

    Go into the connectivity status of the Array and check all the initiators (even the ones in existing hosts) and see if the WWNs for the second HBA are registered to the array.  If they are, verify they are in the correct host.  If not, remove them from the host they are attached to (possible these HBAs were in another host or previously connect to the Array?) and clean them up -- you may have to de-register them.  Then once that is done, re-run the host agent, and try again.  You could also use the UniSphere/NaviSphere Server Utility to manually register the array (first radial option once you run it) with the Host Agent Disabled and then reun the Host Agent again.

    Ted

  • Shaikh1

    29 Posts

    2105

    0

    Posted March 27th, 2012 01:00

    PP is licensed. When I installed PP it was unlicensed during the install and it was licensed after the install manually.

    Cheers

    Sultan

  • tkjoffs

    159 Posts

    2105

    0

    Posted March 27th, 2012 01:00

    You want to do something like this:

    clarDescr

    clarContact

    poll 60

    baud 9600

    eventlog 2048

    device auto auto

    user system@IPADDRESS-SPA

    user system@IPADDRESS-SPB

    Make sure you put in all your arrays that the clariion/VNX will attach to.

  • Shaikh1

    29 Posts

    1380

    0

    Posted March 27th, 2012 01:00

    agent.config set correctly and also added AgentID.txt still no luck.

  • Shaikh1

    29 Posts

    2105

    0

    Posted March 27th, 2012 01:00

    PP.PNG

    Hi

    On first part of the image as you can see host entry has explanation mark which is the Windows 2008 R2 hosts. Whats odd since installing Host Agent and PP software all the Initiators entries has disappeared. I can confirm these initiators were there before these software was installed. Second screen shot shows PP within Windows OS again I can see the storage but some reason I cannot understand why its not displaying second HBA. If you can put me in right direction I would be greatful. This server is standalone box and not part of Microsoft Clustering. Before I go down the route unzoning and rezoning back again want to make sure I am not going down the wrong path.

    Thanks

    Sultan