UNSOLVED

ITMessiah

updated

7 years ago

I

ITMessiah

2 Posts

0

1452

October 2nd, 2019 12:00

Unable to update iDRAC6 from 1.0.36 to.. well.. anything.

Hi all,

I have a PE R710 with an iDRAC6 enterprise that I am trying to update. I am completely unsuccessful and am baffled. 

The firmware of the iDRAC6 is currently 1.0.36.

I have tried multiple firmware revisions (from within windows server OS) and get different messages on each...

Trying to go to 1.20: Failed to start firmware update phase 1

Trying to go to 1.30: Firmware update in progress, please wait 30 minutes before attempting to run an update again

Trying to go to 1.85: Firmware update in progress, please wait 30 minutes before attempting to run an update again

Trying to go to 1.90: Firmware update in progress, please wait 30 minutes before attempting to run an update again

Trying to go to 1.95: Firmware update in progress, please wait 30 minutes before attempting to run an update again

Trying to go to 1.99: "Failed" (This one actually seemed to try, it tool almost 4 minutes for it to fail)

Trying to go to 2.92: "Failed" (This one actually seemed to try, it tool almost 4 minutes for it to fail)

Anything older than on the main dell site was obtained from the old repository here: http://downloads.dell.com/FOLDER00681749M/1/Looking%20for%2011G%20iDRAC%20MONOLITHIC%20Releases.htm

I can't attempt to update via the iDRAC GUI, it doesn't have an option to update.

I've created the SUU disks, it fails with those.

I've used the smart bootable ISO's, that fails.

I can't get into the lifecycle controller, it tries to load then the server just reboots. I can't run the repair on it either, since the iDRAC isn't giving me the options.

I've drained the flea power, removed and reinstalled the iDRAC card....

I'm at a loss. Only thing I have left to try is to run the Openmanage Deployment Toolkit linux thing and see if I Can get it updated that way..

Does anyone out there have any other suggestions??

Help

Thanks

 

  • Daniel My

    12 Elder

    •

    6205 Posts

    1194

    1

    Posted October 2nd, 2019 14:00

    Hello

    It sounds like the iDRAC is not functional. The iDRAC needs to be working to be able to install an update. I would remove the iDRAC express module, turn the system on without it installed, power back down, and then reinstall the module. Power should be disconnected when inserting or removing the express module.

    The iDRAC express module should be a black rectangular piece of plastic attached to the system board. If you are still unable to get the iDRAC to load properly then it will need to be replaced. The module should be included with a replacement system board, you may be able to find someone selling just the express module.

    Thanks

  • ITMessiah

    2 Posts

    1165

    0

    Posted October 3rd, 2019 07:00

    Hi Daniel,

    I can access the iDRAC from the web GUI. I found a workaround to allow me to access the remote console too (downgrade to java 7.x), but nothing I have done allows me to upgrade the module.

    I have done the remove/reseat as suggested previously with no more success. Next step is replace the module then? It is in my home lab, I bought the module seperately so I can get those if needed.

    Thanks

     

  • squigley

    16 Posts

    1059

    0

    Posted October 24th, 2019 11:00

    I had issues with this on an R410 and an R610. My solution was to download the iDRAC update EXE (or BIN), and extract it. It contains a payload directory with a firmimg.d6 file in it. 

    I then put this file on a T FTP server, and I SSH into the DRAC, where I was able to specify the command to update the DRAC with the file I put on the T FTP server:

    racadm fwupdate -g -u -a [IP address]

    Where [IP address] is replaced by the IP of the T FTP server.